89 Johnson 60 HP VRO No Start

rpierson

Cadet
Joined
Jul 5, 2023
Messages
6
I recently purchased this boat knowing it didn’t run right, and I should say I have no experience with boats and or 2 strokes. Previous owner stated motor would flood and wouldnt pee, as well that it would go into limp mode sometimes. Since I’ve purchased it, it pee’s fine, doesn’t flood, and doesn’t go into limp mode. However while idling it seems like it has a misfire or runs really rough from cylinder 3 and will not idle in gear or it wont let me slow without dying, but seems to run well with throttle in gear. I shuffled around the sparkplugs, still cylinder 3. Shuffled around the coilpacks, still cylinder 3. Tested the continuity of the plug boots, and was fine. So I ended up purchasing a new power pack and installed it, went to start it and it will crank and maybe start for a few seconds and die. I tried many times and couldn't get it to start. So I reinstalled the old power pack and the same problem. Any help would be greatly appreciated.
 

racerone

Supreme Mariner
Joined
Dec 28, 2013
Messages
37,831
Some will argue----Step #1 is a compression test.---Post the actual numbers here.-----Does tell tale hose come off the side of the engine block or off the top ?
 

rpierson

Cadet
Joined
Jul 5, 2023
Messages
6
Some will argue----Step #1 is a compression test.---Post the actual numbers here.-----Does tell tale hose come off the side of the engine block or off the top ?
Thank you for your response, my compression test was done with a pretty old harbor freight tester and i got dead nuts 70 on all 3 cylinders, it seemed low but I wasn’t sure since the state of the tester. The tell tale comes out the side next to the engine.
 

rpierson

Cadet
Joined
Jul 5, 2023
Messages
6
Some will argue----Step #1 is a compression test.---Post the actual numbers here.-----Does tell tale hose come off the side of the engine block or off the top ?
Here is a photo of the engine
 

Attachments

  • 01CCA492-280C-4B00-BB00-C10A35D5B3BF.png
    01CCA492-280C-4B00-BB00-C10A35D5B3BF.png
    4.6 MB · Views: 2

racerone

Supreme Mariner
Joined
Dec 28, 2013
Messages
37,831
Does the tell tale hose fitting come off the side of the block , yes or no ?-----Note----I know what a 3 cylinder 60 looks like.
 

racerone

Supreme Mariner
Joined
Dec 28, 2013
Messages
37,831
There was a service bulletin in 1994 to move tell tale fitting from the side of the block to the top of the block.-----I would be taking the head off to look at cylinder walls.----At 85 PSI there might be serious issues.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,095
Your compression is horrible. Is your starter spinning fast enough? Where did you buy the CDI box from? Do you have a factory manual?
 

rpierson

Cadet
Joined
Jul 5, 2023
Messages
6
There was a service bulletin in 1994 to move tell tale fitting from the side of the block to the top of the block.-----I would be taking the head off to look at cylinder walls.----At 85 PSI there might be serious issues.
Alrighty, I’ll take the head off the next free day I have. Thank you for the help.
 

rpierson

Cadet
Joined
Jul 5, 2023
Messages
6
Your compression is horrible. Is your starter spinning fast enough? Where did you buy the CDI box from? Do you have a factory manual?
I’m not sure how its supposed to spin so I couldn’t really tell you if its spinning fast enough. I bought the box from amazon. And no I have not got a manual yet. Where would you recommend getting one from?
*I Plan on taking the head off here soon to check it out
 
Top