89 bass tracker tx17 tournament

eldoark

Cadet
Thread starter
Joined
Dec 15, 2011
Messages
21
new to me a 89 tx17 tournament i need to replace the front decking from the console forward. How hard is it to remove the carpet and the wood. any info on how to do this would be great.
 

Trooper82

Commander
Joined
Nov 21, 2011
Messages
2,648
Re: 89 bass tracker tx17 tournament

Hey there eldoark, welcome to Iboats and the dry dock. There are planty of threads in here of folks doing exactly that, pulling up the deck. Seems a little duanting at first, but once you get started is not bad at all. Some use a reciprocating saw, others a circular saw. I liked the later, was easier to control and setting the depth was much more precise. Just need to be careful not to go too deep when close the edge where the hull is closer to the eck. Also if you have a gas tank under the deck need to pay special attention to that, no kabooms allowed.

The guys on here like pictures, so be sure and post some so we can see what you are dealing with.
 

oops!

Supreme Mariner
Joined
Oct 18, 2007
Messages
12,932
Re: 89 bass tracker tx17 tournament

hi....welcome to iboats....

all of the above !

its not hard.....well ok...pulling the carpet is......but i just cut thru the carpet and skip a step.

post pics and we can guide you
 

eldoark

Cadet
Thread starter
Joined
Dec 15, 2011
Messages
21
Re: 89 bass tracker tx17 tournament

thanks for the welcome. so from i just read the deck is not screwed down? So i just have to rip up the carpet and than cut away the wood? I have read many post on this but did not see how they removed the wood. I will post pic. in the morning.
 

JDA1975

Lieutenant
Joined
Aug 27, 2011
Messages
1,385
Re: 89 bass tracker tx17 tournament

it will probably be screwed or stapled down to the stringers, but if you mean a raised casting deck (by saying front deck as if there is a division) then this wont hold true, pictures or a complete description would help us determine what you are attempting. raised casting deck usually floats. Looking at a video of a boat like yours from consol forward looks like raised deck with storage, will be more complicated to remove and is likely integrated into the cap itself
 

eldoark

Cadet
Thread starter
Joined
Dec 15, 2011
Messages
21
Re: 89 bass tracker tx17 tournament

just ran outside and took some picw with my phone... hoope this will help.. will take better pics in the morning.boat2.jpgboat.jpg I want to replace where you see the line in the carppet up to the console.
 

JDA1975

Lieutenant
Joined
Aug 27, 2011
Messages
1,385
Re: 89 bass tracker tx17 tournament

Is that aluminum? careful not to cut yourself! that will change what i said about it being integrated into the cap though...hopefully one of the tinny guys will chime in on that one
 

jigngrub

Fleet Admiral
Joined
Mar 19, 2011
Messages
8,155
Re: 89 bass tracker tx17 tournament

I believe the previous posters thought you had a fiberglass boat, but you have an aluminum boat.

Removing the deck is easy on an aluminum Tracker, the decking is screwed down through the carpet and all you have to do is find the screws in the carpet nap/pile and back them out.

Start the disassembly with the bow nose piece where the trolling motor is mounted and go from there.

Your decking pieces are wrapped individually with carpet and there's no need to rip the carpet up first.

Your decking might be CCA treated plywood and can be reused. Just pull the carpet off and remove the glue with a belt sander. Check the back of the decking for the CCA stamp.

You'll need to seal your plywood before installing new carpet. Epoxy resin is best for this, but you can use exterior grade Spar Urethane... but it won't be nearly as strong as the epoxy.

Feel free to ask any questions you might have, we're here to help.

Pay no attention to the fiberglass guys, their brains are clouded with glass dust and polyester fumes and they can't even tell the difference between a rivet and a screw... but they're pretty nice guys, just goofy.
 

JDA1975

Lieutenant
Joined
Aug 27, 2011
Messages
1,385
Re: 89 bass tracker tx17 tournament

I believe the previous posters thought you had a fiberglass boat, but you have an aluminum boat.
Pay no attention to the fiberglass guys, their brains are clouded with glass dust and polyester fumes and they can't even tell the difference between a rivet and a screw... but they're pretty nice guys, just goofy.

Is that aluminum? careful not to cut yourself! that will change what i said about it being integrated into the cap though...hopefully one of the tinny guys will chime in on that one

yay lol I redeemed myself 2 minutes before you caught me! lol Jig thanks for jumping on it and setting him in the right path...once i saw it was aluminum, that changed everything I previously said...but still be careful not to look at it wrong lest you suffer the curse of many cuts!
 

eldoark

Cadet
Thread starter
Joined
Dec 15, 2011
Messages
21
Re: 89 bass tracker tx17 tournament

well today i took out all the wood from the console forward. wasnt to bad of a job. tried to load pic but kept saying it failed... will try again later
 
Top