1978 imperial tri hull repairs

jcoop86

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
13
Hello, so I just picked up a 1978 imperial 16' Trihull for very cheap. Obviously because of the age and the price I've got a good amount of work to do. Fortunately the Johnson 115 that came on it seams to run great, at least out of the water on muffs it runs great. I've torn up the deck and started ripping out the slightly water logged foam. So now I'm getting ready to start on repairing the stringers. I have one variable on this boat right now, the transom has been repaired before. The repair was done without separating the top and bottom and not very much cutting on the back, it consists of new wood ( about half as tall as the factory wood would have been, doesn't go all the way down but the wood is very solid) and aluminum plate that covers the entire outside of the stern, another aluminum plate on the inside of the stern so the wood is basically sandwiched between the two plates and there is a third small plate on the upper inside of the stern. Does this sound like a decent transom fix, it feels very solid, with the motor up I can grab the bottom by the prop and lift up and down very hard and there is zero flex in anything on the stern. Seems good to me I just would like some input from some more experienced boat repairers. The wood not going all the way down is the only worry I have, not sure what I'm worried about but I am. Any input from you guys would be greatly appreciated and I'll try and get pictures posted
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Hmm Pics for sure are needed. I'm not a fan of this type of repair but...Maybe they did a job that's better than most!:pray2:
 

jcoop86

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
13
Let me know if you can see the album in the post above, I tried it and it worked for me. I've never done the photo bucket thing so I don't know if I did it right
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Nope no pics. Once loaded into Photobucket just copy and paste the IMG code directly into you iBoats thread.
 

jcoop86

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
13



tobucket.com/albums/cc367/jcoop86/Mobile%20Uploads/image_zpslawmpks0.jpeg[/IMG]
 
Last edited:

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Uhmm Yeah!!!! IMHO IF you want to keep the boat for any length of time and want to be SURE that it's safe, then I'd rip of all the aluminum plate both inside and out and rebuild it the way it should be built. It's really not that hard. Just and FYI!!! Due to the boats age I'm pretty sure you're gunna find that the stringers will need some attention as well. But Hey, it's your boat and you can do with it as you see fit. You're on site and If you think it's structurally safe and you're willing to put your passengers in it and get on the water, then Happy Boating. Just make sure everyone has PFD's and you're aware of your surroundings and can notify others when and where you'll be in case something happens.;)
 
Last edited:

jcoop86

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
13
I'm definately doing the stringers and the deck, like I said I was questioning the transom bu between the new oak that was put in there and then the aluminum on top of it , it is super strong, no flex whatsoever. I just don't understand why they didn't run the wood as far down as they could. The wood goes down between 50%-75% of the way to the bottom. It just seems weird to me, like they repaired it 75% right but then used the aluminum plate to compensate for the last 25%. And that's also 5/16 aluminum plate also so that repair wasn't cheap either
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
As long as it's not flexing it should be ok but it appears to NOT be sealed and anytime aluminum plate is used on a Fiberglass boat it is NOT the correct way to do the job. Oak is NOT the preferred wood for a transom. If it is White Oak it's not too bad but In actuality plywood is much stronger and better to use. Keep and eye on it. I just hate to see you do the deck and stringers and NOT the transom and then later on have to rip the deck out and cut portions of the stringer away to have to do the transom when you're gunna be in there now.;)
 

jcoop86

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
13
I think for me personally it's gonna come down to what it does when I set it in the water, after I finish clearing out the old foam and a couple more small pieces of decking, I'm taking it 5 min down the road to put it in the water but leave the trailer under it and see what I've got for water coming in. If it seems to be well sealed i think I'm just gonna do the stringers and deck since the transom feels solid as could be, it just doesn't look right, but if it takes a lot of water back there then all bets are off
 
Top