1978 85hp Johnson timing issues

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
I'm going to say something looks out of whack with that throttle arm. It's leaned way to the rear of the motor, and the link to the throttle cam appears to be adjusted way forward. Seems as though flywheel alignment is off. If you're having trouble getting the nut loose, just do the TDC check. Take #1 plug out (highest plug on motor). Put a long screwdriver straight into the plug hole and rotate the motor until the screwdriver is out as far as possible. Look at the pointer and see where it aligns on the flywheel.

Oh, and I don't think that's the right rectifier for your motor if the two lugs don't span the two mounting points. Note that the two bolts to secure it are different sizes. If loose, your charging system won't work properly.

This is how my '82 90 looked before I took it apart. Note the throttle arm is pretty much vetical and the nylon adjuster for the cam link is threaded much closer to the throttle arm. Now I'm not saying it's wrong necessarily, but it looks really really odd.

 

98SkeeterSS90

Seaman
Thread starter
Joined
Jun 28, 2016
Messages
54
Looking at the peened ends of your throttle shafts, it doesn't look like the carb butterflies are closed.


By looking into the front of carbs looking at top of blades they are both indeed sealed. Bout to do top dead center
 

98SkeeterSS90

Seaman
Thread starter
Joined
Jun 28, 2016
Messages
54


This is where pointer lines up with the #1 spark plug out and screwdriver pushed as far out as possible.
 

98SkeeterSS90

Seaman
Thread starter
Joined
Jun 28, 2016
Messages
54
What can I spray around the motor to make it rev or go down when there is a vacuum leak? I tried electronics cleaner but it seems to seep thru fuel hoses and makes it idle lower even when I KNOW there isn't a leak on the side of a brand new hose.

If I can't figure it out this weekend it's going in the shop reluctantly next week and I'll update with what they find. Hopefully it don't cost me an arm and a leg
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Spraying electrical cleaner shouldn't change idle rpms, imo, assuming you aren't spraying around the carb intake. Maybe it's a leak at one of the carb mounting gaskets, maybe a loose mounting nut.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Safe enough if you do it outside, but don't if you're not confident. Aim the nozzle at various gaskets and cracks while the engine is running. Likely worst thing that could happen is a spark lights the torch, but there won't be enough gas around to cause a problem.
 

98SkeeterSS90

Seaman
Thread starter
Joined
Jun 28, 2016
Messages
54
Tried putting boat in water today and it idled like it should BUT wouldn't run longer than 15 seconds back to square one. Put it back on muffs and trimmed it up and it imitates when in water on trailer.

Did I mess something up rebuilding carbs? Runs fine just high idle on muffs with the engine level, trim it up and it cuts off
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Old motors like that, with all that paint splashed all over will never run well !!
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Make sure you have the needle valve spring clip attached to the needle and hooked over the float arm. In case the rubber (Viton) tip of the needle sticks in the seat hole, the spring will let the weight of the float pull it out. Float parallel to the bowl when flipped upside down. Float drop spec exceeds the space inside the fuel bowl for the float to move, so I'm not sure why they bother with it.
 
Last edited:

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Old motors like that, with all that paint splashed all over will never run well !!

With good compression (which it has), it's more a matter of finding and fixing all the worn parts to make it run right. I hope the gearcase is in good nick.
 
Top