1976 Forester Trihull

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
I am a novice in the boating world that picked up a free 14' forester trihull from my father in law. It was covered but in the elements for a number of years, and then garaged for periods of time. We got the 1972 Johnson 40HP to fire and run on the second try, so it has it's good points. Like many of you would expect, the floor has some soft spots. I have read the forums for weeks trying to learn what I can about the floor/stringer structure and the process of replacing it.

I'm ultimately looking for a simple fishing boat on small lakes that my wife, daughter and I can enjoy. I haven't pulled up the floor at this point, but was wondering if anyone had any experience with this specific style/model of boat and could provide a little information on the sub floor structure. I can feel no give in the center beam, or the beams that appear to run front to back along the very sides of the hull. The two areas that on either side of that main beam do have some give.

Today I found a post about the use of foam in trihull floor structure for support between beams. Is that typical? What is going on down there?

Hopefully these will help give an idea of what she looks like
20160703_142625.jpg

20160703_145601.jpg
VZM.IMG_20160626_150437.jpg 20160626_150243.jpg 20160626_150234.jpg

Thank you in advance for your time and advice.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Typically Tri Hulls will have 2 to four stringers below deck and possibly some cross bracing. They're not all alike. I'd just cut it out and then you'll know. Have you inspected the transom?
 

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
Thanks woodonglass. I was hoping someone had experience with this particular model so I had a better idea of the structural elements of the boat. I'd like to use it some this year before deciding whether to tear it apart or not. From all accounts it appears to be an expensive and lengthy process. More so because I'm not familiar with the chemical's and processes in the many threads about this topic. Plus my wife would be on my a** about yet another project I have sitting around! VW bus camper, dirt bike.... you get the idea.

This old thing is not exactly most people's dream boat so I'm a little hesitant to drop too much cash in it. I'd like to see if our family was interested enough in boating/fishing with this one so we can consider if it made sense in the long term to buy something nice or nothing at all.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
You MUST core sample the transom and OR Bounce on the lower leg of the motor to see if it has any flex in it. Soft decks, many times indicate more problems below. If the transom is flexing I wouldn't advise using the boat.
 

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
I'm interested in your opinion on the transom. I put a good deal of pressure downward on the lower half of the outboard. It was enough to make the boat move
 

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
Here is the video I referenced in last post. Let me know if it won't play.
 
Last edited:

sphelps

Supreme Mariner
Joined
Nov 16, 2011
Messages
11,508
You must have your PB set on private ..
Pretty clean looking tri hull ! And your tow rig already matches ! ;)
 

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
Sorry about that. I moved it and hope it works now.

Thanks sphelps! I shined her up a little bit, but it definitely matches the jeep. Sometimes these things just work out..haha.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Based on what I can see in the video, your transom appears to be solid. Is the floor soft in alot of places or just a few? Where are the soft spots located? Middle,sides or corners?
 
Last edited:

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
The soft spots are mostly from the console back. There is a very firm center stringer, and two outside stringers up against the very sides of the deck. The portion in between the center and the side edge on each side is what I've found to be soft. It's not just one spot, but rather from about 2 ft forward from the transom up to the steering wheel on either side of that main beam. I wondered if this type of boat had foam support between these stringers and it no longer has the "fullness" it used to.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Probably no foam on this age of boat. It COULD be that the MFG use a thin flooring material and it's flexing. I know some of the vintage boat MFG's did that. Is it REALLY flexing or does it feel like it might just be from thin decking? You could drill a 3/8" hole into the deck and see how thick it is. Easy to fill the hole with thickened resin once you find out. I'm thinking it will need to be replaced but... Don't want to say for sure quite yet.
 

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
That's something I hadn't considered. The flooring does feel pretty thin, but I don't have a lot to compare it to b/c my own lack of experience vs what many of you folks have. There are some holes already where the back to back seats were previously installed. Their holes were not aligned with any of the solid (left edge, center, right edge) portions of the boat. I'm not sure if the seats in this period were simply screwed into the deck. Anyways...I think I can try to use one of those seat bolt holes to determine depth of the deck without drilling another. Does that sound plausible?
 

TheRedDragon

Cadet
Thread starter
Joined
Jul 6, 2016
Messages
23
The depth of the holes that were previously used to mount the seats was about 1 to 1.5 inches deep. There is a section in the deck floor that has a crease right under where the drivers seat would be. shined a flashlight in there and with a screwdriver scraped up a little material. It seems like there is about a 1 inch gap between the deck floor and what appears to be wet plywood. My boat cover slipped the other day so I'm sure that's part of it, but the gap seems odd to me. The deck floor is as thick/thin as cardboard and doesn't seem like it would be firm without some reinforcement or solid backing.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
See if you can post some pics of the deck. Not to close not to far. I for one can learn a lot more from a pic than I can from text.
 
Top