1960 Glastron FireFlite has a new home!

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Thanks PMC, it was a tough end to 2011. The little guys are enjoying a little extra attention & all the reclaimed real estate on the couch.:) Leaving for a week out of town wasn't easy w/ out the big guy at the door. Coming home later this week won't be the same either...... But all things in their place & time. Majic's time with us ended too early, but it will allow us to rescue another in need.....

I get stuff sent to work all the time, mostly so it's not sitting outside our front door for 5+hrs post delivery. The UPS & Fedex guys are like clockwork at work, by noon everyday:rolleyes: But at home??? Anytime 11a-8p.....Plus we have a dock so it's much easier to off load a pallet anyway. If the materials actual costs won't be expensive enough, the hazmat freight just makes it worse...... I really need to spend some time figuring out an estimated materials list for resin, glass, filler & etc. That way I can hit on a deal if I find 1. I have 1 possible source for laminating unwaxed resin but it's still almost $40/gal delivered. I'm a ways off from glassing the transom & deck, so I've got some time.......

Nice score on your hoist & drill adapter! Getting the 650 hung on my transom w/ out the hoist was an boondoggle I never want to repeat!

I had some time after work today & toured the lumber & tool departments of both big box improvement stores (L & HD) then looked at compressors & heaters. Spending some time planning to improve the garage so I can get some 'glass work done this winter has kept me busy. The big grinder day over the weekend was a good distraction too.

Look forward to building through your progress, thanks for stopping in w/ the condolences.
 

GT1000000

Rear Admiral
Joined
Jul 13, 2011
Messages
4,916
Re: 1960 Glastron FireFlite has a new home!

Wow JB, really sorry to hear about Majic...May Gypsy help to fill the void...and I totally agree...

Rescue Dogs Rock and Rule!

and on another note, dang it, 40 bucks a gallon for resin, man-o man, here I thought 25-30 was a lot...I sincerely hope you can find a good deal...Check USComposites, cause even with the hazmat fee, I think it is still less than 200 bucks for a 5 Gallon bucket and you might be able to score some kind of freight shipping for the whole load???

As always, Best Regards.
 

Pmccraney

Lieutenant Commander
Joined
Jul 26, 2011
Messages
1,734
Re: 1960 Glastron FireFlite has a new home!

WOG posted this on another thread... Not to speak for him, but I thought this was a good, concise list of what you need to put on your shopping list for materials:

"For an 18ft boat, doing stringers, deck and transom you should probably start with the following...

435 Resin 15gallons
5 qts of Cabosil
1lb of 1/4" chopped strand
1 qt microballons (to make your own fairing filler)
25 yards (1 Roll) of 1.5 oz CSM Chopped Strand Mat)
10 yds of 1708 Biaxial cloth
Fiberglass Roller

Everything else you'll need you can get locally.
Check the link in my signature for Recommendations on how to do it all/with drawings.


That's my suggestion for your Order."
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Thanks PMC, I don't have to replace the stringers (YEAH!) but once I get all the cutting & grinding done, I need to look them over & make sure all of the glass stringers are still 100% attached to the hull. It seems to look like they were an integral part of the initial layup, not added & tabbed/glassed in. At 15' I won't need quite that much either. It looks like I had WAY over estimated the 1/4 chopped strand, micro-ballons, & cabosil. I looked up a few supplies @USComposites last night and had made a mental list of what I thought I needed..... Cloth was close, but I had less CSM & more 1708, but only slightly. And 10gal of resin. Which might be a tad too little. Especially if I need to re-tab the joint at the hull to cap connection, which is how it was originally.

Thanks again WOG!

And PMC for posting WOG's material list here!
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

In case anyone missed my locale: WVU crushed the Orange Bowl in Miami Wed pm! Not a big fan of college football, but damn, set several new scoring records.......
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Thanks to our friend WOG's list, I started getting quotes for materials & supplies. It looks like FiberglassServices.com in FL is cheaper on 3X 5gals of resins delivered to me. All else will be from USComposites, who are at least $100 cheaper on everything else. Basic resin, glass & fillers, total from both outfits is @$675, delivered to my office dock via freight. I won't place an order until at least Feb, but may wait til mid-late March. I have problems w/ other materials I order for work coming out of FL to WV & having freezing problems with our materials not being protected in shipment. Of course, if I can get the rough work finished, I may not be able to wait 4-6wks to order glass. I'll get the ply situation figured out before Feb too. But no reason to have the ply w/out resin/glass.

Tried to order some HarborFreight supplies today when I got home. When I confirmed my order, their server was undergoing maintenance, and my cart had been emptied:mad:. I'll try again later tonight.

Have a great weekend. We're taking the remaining crew to the do park, happy tails all around:cool:
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

I also priced 4X8 sheets of 1", 1.5" & 2" pink foam sheets at Home Depot, which will probably get my ply business. Unless Lowe's happens to have Aurauco ply when I am ready to order/buy it. Their lumber buyer finds a 'deal' on it & orders it a bit randomly. Some get it regularly, some never do. I also tried 3 regular lumber/wood yards for MDO & ACX ply, they were all $45+/sheet, w/ a 2wk lead time. I have some time:) so I may go ahead & decide to spend the extra $45-75 to get better material. Not going to fight lower quality ply, to save less then 5% of the total budget...
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Re: 1960 Glastron FireFlite has a new home!

Really sorry to hear about your dog. Been there done that and it ain't kool. There is absolutely nothing wrong with using the Arauco Plywood. It is very good stuff and if you glass it right and maintain it properly it'll last 30+ yrs EASY!!!!! I really like MDO but it's hard to find and there is a big difference in suppliers etc. Check with Sign Shops in your area and see if they have a distributor. They will have the good stuff.
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

WOG: As their caretaker it is something I know will come 1 day, never ready for it.... Glad to know it makes the MRS a wreck every time. It will take her more then a second to think about it when its time to pull the plug on my respirator.....:rolleyes: I always think of them as leaving us to go out & find another who needs a home & sends us their way:)!!!

Yeah, not a lot of call for anything other then BCX ply anywhere close to home. Arauco is iffy to even find (just once a month ago, 4hrs from the house in my work car:facepalm:) and no one yet will order it. MDO & ACX are available from a couple places as special orders, and I think I'll end up using MDO. The sign shop I called said they use MDF, & I asked to make sure they didn't mean MDO. Nope 'that stuff that looks like a 1/2" thick paper grocery bag'.... Nope, thanks, wrong stuff!

I think the last place was $45 for a 4X8 1/2" smooth 1 side MDO, 2 weeks lead time. If I have to order it, I should order the least likely to arrive pre-warpped since I won't be able to cherry pick 3 sheeets out of a stack 25-30 sheets. And after a 2 week wait, I won't be too happy to reject a sheet or 2 and wait another 2 weeks:(.......

Thanks for keeping tabs...

The crew enjoyed the park! Gotta take the high 40's days when we can. Back to the bad weather early next week.....
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

The hunt for parts continues, got a 'new' steering wheel & hub today... Yeah, I sat at my desk, held the wheel & played a Merc 650 video to 'mock' it up for the wife. She gave me the other look, you all know the 1: The "is ya 'touched' in the head look...."

I may not be able to wait to rehab this wheel. My Glastron symbol center section is a very close fit.... We'll see how that plays out......
IMAG0328.jpg
IMAG0329.jpg
IMAG0330.jpg
IMAG0331.jpg
IMAG0332.jpg
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

I may be missing something, but in all the reading I've done & videos, it seems to be quite a bit of PB to get everything bedded & filleted in. By the case, 12 large construction tubes (28oz ea), this:
PL400.jpg

is <$59, shipped from the big orange box store's website. And don't think I'll use it all. Opened tubes will have 'some' shelf life, un-opened, protected from freezing/heat, tubes will have a fairly long shelf life. Unlike resin that has an unopened shelf life of 6-9mo, opened resin is probably much shorter. If I use 75% (9tubes) that's @$45, which is very comparable to what I'd pay for shipping most of a gallon of resin & some portion of the 1/4" chopped strand + cab-o-sil. Thinking that I'd use at least 2/3-3/4 of a gallon of resin to make fillets, that's 'only' 2.5-3qts. W/ the PL I won't have to worry that it will kick off before I finish applying all the PB I mixed. Nor will it take very long, when I run out of the PL in the gun, to grab a new tube & keep applying it. It isn't that time consuming, but mixing additional PB batches will take some time, and as a rookie maybe longer. My actually thoughts were to bed the deck onto the stringers w/ PL, then fill & make a small fillet at the deck to hull joint. After cure, make a 2nd pass w/ PB to create nice smooth transition coves at the deck/hull joint. I may need to re-think this some.

Of course w/ wood-free, fiberglass only stringers, I won't have nearly the PB in my deck put back then some or most do, since I won't be doing new stringers. But I do have 3 ribs, ply deck joint backing, to re-install (deck ply cut into 2" wide strips pre-wrapped w/ resin & CSM, matches factory ribs). They were originally 'let' into notches cut in the tops of my glass stringers. I had planned on PL for them too.

Feel free to disagree w/ me, or harsh on my 'plan'. I welcome all comments. Besides I've earned some abuse, gotta be able to take it to dish it out.

Thanks &

TGIF!!!

Well, the snow & cold may keep me from grinding this weekend, but 50+ on Mon & I just found out I get MLK day off paid!
------> Insert Snoopy happy dance here <-------
 

bear_69cuda

Commander
Joined
Oct 10, 2008
Messages
2,109
Re: 1960 Glastron FireFlite has a new home!

Hey man,

Sorry about your dog... I've been there and know how it feels... My buddy Jackson Lee has reconstructive knee surgery in two weeks... poor guy... He blew it out at the dog park last month. Sorry about the off topic, I was just reading your thread catching up, and wanted to say sorry for the loss... Great pack of dogs you have dude! Liked the pictures!

peace out-
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Yep, we take great comfort in knowing that by leaving us, Majic made room for us to adopt another in need. Looking forward to meeting & bring home our latest rescue. Not the best time to drive to Buffalo, NY but we may luck out & get to see Niagara Falls:) next weekend if the weather holds out.

Our pack will send Jackson all the good thoughts we can. They are remarkable healers & overcome great obstacles w/ ease so I'm sure he'll get a dog park pass soon after surgery.

Thanks for dropping in & the condolences. I actually tried to change my signature pix to the 1 we got pre-adoption of Majic, but can't seem to get it to load now that I've deleted my original signature pix.
 

craigweaver

Chief Petty Officer
Joined
Oct 24, 2011
Messages
550
Jb, I have a 13yr old chocolate labe I rescued 10 yr's ago. He's the best dog I've ever had. He's starting to fail and I just can't give him enough love every day. What an awesome bUild you got going there bro. CN't wait to see how it shakes out. My Mrs just shakes her head over my project but so far she's on board with it. Can't wait to see how the rest of yours goes.
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Yeah, the end is a part we accept as their care giver. But even older & feeble, we're still never ready when they tell us it's time for them to leave. Hope you still have lots of days to share w/ your lab. Good thoughts ya'lls way! Can't ever say enough good stuff about rescues!

Thanks for joining our rehab journey. We've got a bit to go, but looking forward to a bit o grinding between now & Mon pm. Get some more of the deck hull joint ground smooth & work on a bit of the transom too. The hull/cap joint is going to be a task, but if the weather improves some, I may get onto some of that too.

I need to push the hull back 1/2 out of the garage to grind. The garage is under the master, & the MRS isn't a fan of the respirator:eek: but w/ the cold weather, I'm going to be a ways off before I glass anything for the same reasons.

So stay tuned, small progress shall be measured monthly! Not by the minute in the early am like our favorite northerner, novice (yeah right;)), tinny, SC Islander rebuilder.:) His tenacity & persistence is very motivational! And w/ good looking results to boot!

Everybody get to work! It's the weekend! Have a good one! Seriously all you guys w/ heated garages & in warm climates need to give us northern popsicles some inspirational updates!
 

sphelps

Supreme Mariner
Joined
Nov 16, 2011
Messages
11,508
Re: 1960 Glastron FireFlite has a new home!

Hey jbc, sorry about your dog.. I know how it feels . (Smokey) in my avitar on the left was the best. Cried like baby when he passed.
Anyway, don,t sweat making the PB just make a 1/4 or 1/2 qt at a time mix the resin and fibers first then add cabosil. Tap in a little at a time and mix till you get the stiffness you want apply that and mix some more. The first batch I made was to loose , the rest was right on time.
Well lunch is over got to get back to cleaning my work space, I can hardly walk in there.:eek:
See ya S.P.
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Thanks SP!
The project has kept my mind busy, but yeah, hanging out at home this weekend has been tough.

I'm still a bit from deciding the PB~PL question, until it's at least 35 outside, the MRS has me in a holding pattern on grinding. So it will be at least Mon before I push the rig 1/2 out of the garage.:( This project cost me some shiny new bling for xmas, I'd really like to not have to repeat that at Valentine's Day.:D

Got's to keep the MRS happy, we don't want no "all skillet all the time" show like Jas predicted at his place!:facepalm:

So lurking, reading & learning here at iBoats this weekend!
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Well, I feel a little left behind since it's a long weekend & I haven't made any progress... Since it's threatening to be above 30 by noon Mon, & I have MLK day off, I may push out her of the garage, tarp the cockpit & grind a bit! At least try to get the remaining deck/hull joint ground smooth, it may prove too cold in the drive way to grind under the splashwell & transom.

Have a great week!
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

Spent some time in my tyvek suit today, man it's warm. Even w/ 1/2 the boat in the driveway, as long as I was grinding, I was nice & toasty. Too bad the grinding 'glass smell made it into the house.......Red card on the job site---Shut down:(. At least I was able to contain the dust. That would have been a whole different situation.

I was working on the edge of the seat bases glass joint at the deck/hull corner. They laid that stuff on thick! Although it does seem to have quite a few air bubbles.

I got some more of the deck/hull joint ground smooth too. I will have to go back once it's all done & cleaned up. I'm not hitting it all up high enough to allow the new poly & glass to get a good bare surface to bind onto, just working the actual joint.

I also spent some time looking the cap/hull joint behind the rubrail. The rubrail doesn't have a rubber insert, so it's got blind bolts thru the hull. I'll need to get some close up pix, but I'm not sure if I can save the rubrail & get the cap off. The cap joint & rubrail bolts are BURIED (!!) under a lot of poly & glass. It's probably going to be tough to get new rubrail to conform to the inside & outside corners w/ my limited workspace & experience. I'm not sure which thread had it but heating the new aluminum rubrail & bend it around a wooden buck form. How much 'play' is there in a rubrail channel? Enough to make these bends & still have a new insert fit/work? I guess another alternative is to have new blind bolts installed on the back of my existing rail.

Rubrail.jpg

Bear with me, I may not make much progress this week, & out of town this coming weekend. Hope to be picking up our new crewmember! (Weather permitting) If we make the trek to Belfast, NY, we may try & see Niagara Falls, & may grab a 650 merc parts motor, & a 650 short shaft motor. We'll see.....
 

jbcurt00

Moderator
Staff member
Thread starter
Joined
Oct 25, 2011
Messages
25,350
Re: 1960 Glastron FireFlite has a new home!

I just had a thought, I may have picked it up from the rubrail & buck form thread I mentioned ^^^

If I insert a correctly sized spacer into the insert track on the new rubrail, & then make the bends around a buck, will that preserve the track enough to allow the insert to pass through it, still allow me to bend the rubrail, and keep the insert in the rail?

Hmmm, as I'm typing this, it occurs to me that a spacer would have to be flexible enough to allow bending of the rubrail, but firm enough to maintain the insert track, AND be heat resistant so it could be inserted before I put a torch to it. I'm not sure what I might have access to that meets those criteria..... Hmmm....

I'm off to do a thread search.....
 
Top