Search results

  1. fishermanms

    1989 115 Mariner 4-cyl will not tilt up

    Hello, been a while since I've had to post a problem but I got one and I think its minor. I hope. I own a 1989 Mariner 4 cyl w/power tilt & trim and today when I was ready to leave the lake, I trimmed down and took off and ran to the boat landing. I noticed the tilt/trim button would not trim...
  2. fishermanms

    Should I replace the bearings???

    My old trailer for my 14' John boat is about 40 years old. Ive had it for 30 years and never replaced the bearings . I recently refurbished it, (painted it, new lights, new rims and tires, safty chain, tougue, etc.) But I did not replace the bearings, I just shot a bundle of marine grease in...
  3. fishermanms

    Will a cotter pin work as a shear pin?

    I sheared a pin today when I bumped a stump with my lil 6hp Johnson. Was ust wondering if I could use a cotter pin as a substitute for a day or two till I get some new ones....Or anthing else that might work. Thanks for any advice...Fishermanms
  4. fishermanms

    a lil help needed for trailer wiring....

    I just finished wiring up my old aluminum boat trailer that I just finished restoring. I got my lights mounted up high to keep them out of the water. I'm using the 4 flat hook-up on my 2004 F-150 Super Crew. Trailer Brake lights work fine both sides. Turn parking lights or lights on truck on...
  5. fishermanms

    19?? 5hp Otasco been idle for 29 years..pics

    I dont know much about this motor. I bought it in 1978 from a small engine repair shop. The old man that owned the shop owned the motor and said it was a good motor and run good. He's dead now. Its a Otasco 5hp 1 cylinder two stroke. I think the motor may be a B & S. I took it out one time and...
  6. fishermanms

    Do I need gasket sealer on this homemade t-stat gasket?

    I bought some gasket material for my 74' Johnson 6hp T-stat cover, cut out almost a perfert gasket, installed it and did a tank test. There is no t-stat in there. But my new t-stat, gasket etc will be here next week. I cranked it up in the tank and for what ever reason it takes it about 1/2...
  7. fishermanms

    Removed T-Stat cover..no t-stat there,someone removed?

    I removed the t-stat cover from my 74' Johnson 6hp and in the cylinder hole there is nothing. This model requires one, so I will order it and the gasket. In the meantime, can I run it without. I bought some gasket material, various thickness sizes and will cut one to fit. Will I be ok till my...
  8. fishermanms

    Can I make a gasket from a fel-pro gasket?

    I was brain storming... I need to order a gasket for the t-stat housing for my 74' Johnson 6hp. Trying to save some money on freight. Could I just take a felpro gasket about the same thickness and cut one out to fit? I've got plenty left from a rebuild on a 400 sb chevy. Is this possible if I...
  9. fishermanms

    1974 Johnson 6hp Lake Test Results...

    This morning my wife and I loaded up the 14' shallow well narrow aluminum boat we just finished patching and painting and installed new transom board and the 6hp Johnson we just rebuild. We took them out to a local public 600 acrea lake for the final test. She cranked up after a few pulls...
  10. fishermanms

    Finally got 6hp cranked...BUT no water out of exhaust

    Re: Finally got 6hp cranked...BUT no water out of exhaust IWOMBAT, OK.... Good News!!! Don't send money yet... I cranked it up, she warmed up alittle and I got a good stream of water out of exhaust!!! by the way, she sounds nice and smooth......... BUT.. On top of the head above the plugs back...
  11. fishermanms

    Does a 74' Johnson 6hp have a T-Stat??

    Does any body know if a 1974 Johnson 6hp has a thermostat??? I had another new thread goning related to this thread. I searched my manual and cannot find anything a bout a thermostat. Please look at the thread : got it cranked BUT no water coming out of exhaust... TY Fishermanms
  12. fishermanms

    Finally got 6hp cranked...BUT no water out of exhaust

    I finally got the Johnson 74' 6hp cranked... Took a little pulling to get the gas to the chamber but it cranked. I had my wife behind watching for water to be coming out of the exhaust. But just smoke is all she could see. I shut it down immediately. I had put in a new impeller, changed the gear...
  13. fishermanms

    Just exactly where is TDC on the cam??

    I have installed new points, condensers and coils on this 1974 Johnson 6hp Model 6R74-C. I am trying to discover exactly where TDC is located on the cam. I have line up the points to the O, located in the word TOP. I know that wherever the points opens the most is the location, but to the naked...
  14. fishermanms

    Grease coming from shaft vent holes????

    OK, here is a Johnson 74' 6hp, In the middle of rebuilding carb and installing coils, points and condenser. About ready to put the armature plate back on. Carb is still off. Behinf the carb and right above the intake manifold and back behinf that the shaft housing rises up...Those two holes...
  15. fishermanms

    Powerhead retainer question

    Im about to reinstall the armature plate back on... I noticed that the powerhead retainer with the four holes that the armature plate is screwed back to is loose and will wobble. Is that normal??? I can reinstall it and I guess that will tighen it back up??? Just wanted to make sure this is ok...
  16. fishermanms

    Armature plate removal on 6hp Johnson

    While I'm waiting on a float for the carb to get here, I wanna go ahead and install points, condensers and coils. I was just wondering if I can remove the armature plate with the points, condensers and coils still intact?? Then I could move the armature plate with everything intact from the...
  17. fishermanms

    Should I replace this ugly deformed float??

    Re: Should I replace this ugly deformed float?? It is deformed to the left of the assembly, where the cork had collasped at one time or another somehow. It is dry but looks wet because of what looks like varnish painted on it some time ago but other than the slight collasped area its ok. It may...
  18. fishermanms

    Should I replace this ugly deformed float??

    I got the carb offf and am in the process of cleaning and installing a carb kit. Unfortunately my kit dont have a float. Click on the pic below and look at it and tell me what you think about it, please, and should I replace it??? If I need to replace it, should I order one here or run up to the...
  19. fishermanms

    Will this fuel pump fit and work?..pics

    Re: Will this fuel pump fit and work?..pics I got the pump on with longer bolts, ( I had to cut two 2" down to about 1 3/4", turned the big gas line toward the incoming gas line, the small one going to the carb is on top. A pic of it is below, click on it and look... My question is.. Will the...
  20. fishermanms

    Will this fuel pump fit and work?..pics

    I ordered a new fuel pump from iboats for a 1974 Johnson 6hp model 6R74-C. They both look pretty much the same. The one I ordered said it fit 6hp Johnson 1992 and earlier. It also said it replaced OMC and after that four different part numbers. Im not sure what the part number is on my original...
Top