Search results

  1. B

    7mm spark plug wire crimp or spring type connector??

    Replacing Older johnson outboard with 7mm copper core spark plug wire. Which type of spark plug connector is better old spring type that pushes on thru wire jacket or newer crimp on type? Thanks in advance
  2. B

    Johnson evinrude drain plug washer

    Anyone know where to get bottom end drain plug washers for older johnson evinrude in bulk ? Are they nylon or teflon ?
  3. B

    Where to get replacement spark plug wires for 1976 evinrude 4hp??

    Found some copper core wire at a dealership only markings stamped on it say Nakaya . Anyone know who made this stuff or if it any good?
  4. B

    Where to get replacement spark plug wires for 1976 evinrude 4hp??

    Need to replace damaged spark plug wires on 1976 evinrude 4hp . What are best type to replace with and where can i get them at a fair price. I cant find exact specs or any info on replacements.
  5. B

    1976 evinrude 4hp fuel pump rebuild or replace with newer model

    Is oem kit better than sierra kit? Also are the aftermarket pumps any good or just a crapshoot? Just want to have one incase it wont run after i get it all reasembled
  6. B

    1976 evinrude 4hp fuel pump rebuild or replace with newer model

    Just put carb kit in, motor not run for years carb was gummed up with old gas and figure the pump might be the same. How long do the rubberized gaskets / diaphrams last in these pumps? What would be the symptoms of a failing fuel pump?
  7. B

    1976 evinrude 4hp fuel pump rebuild or replace with newer model

    I have a 1976 evinrude 4hp 4606m , anyone know if thry make a rebuild kit for it or if you could use a fuel pump off one in the 1980's. The fuel pump number is 388684 , i saw a rebuild kit # 393088 for johnson/evinrude 1981 up. Looks like same gaskets in the 76 fuel pump. Does anyone know if kit...
  8. B

    2hp evinrude gear case re-seal question

    1982 evinrude 2hp -- Have gear case apart , do you put any type of sealant on the outer surface of the new prop seal/gear case housing, same with shaft seal under water pump? Also is there supposed to be a gasket or sealant where gear case bolts to the exhaust housing? If there is what kind of...
  9. B

    1982 Evinrude 2hp gearcase full of water

    Have a 2hp evinrude, went to change gear oil and over half full of water. Anyone know how to replace the seals or what i will need to take apart to get to them? Can't find any info on how to replace them
  10. B

    Looking for Service manual for 1982 evinrude 2hp (E2RCNE) outboard

    Replacing coil, points and pull the clyinder and piston
  11. B

    Looking for Service manual for 1982 evinrude 2hp (E2RCNE) outboard

    Does anyone know where to find ,or download a copy of a service manual for a 1982 2hp evinrude outboard model#E2RCNE , that is just for that year and model. All i can find are ones that cover a wide range of years and models. Closest i have found is for a manual for 1980.
  12. B

    16ft lund aluminium boat add kicker motor

    I have a 25hp motor on an old 80's 16ft lund aluminium tiller type boat. Want to add a small 4hp outboard kicker next to it. Problem is that the kicker motor doesnt get full swing next to the 25hp with the handle down . What would be best way to mount it ? Adjustable Outboard motor bracket?
  13. B

    16ft Lund aluminium boat rivet size for bottom hull?

    Just drilled out some rivets from under a 16ft aluminium fishing boat tiller type , i have 3/16 inch rivets for it but when the rivets were removed the hole size on all of them are exactly 13/64 and the 3/16 rivets are loose fitting. Drilled out a couple that werent leaking and the same hole...
  14. B

    Lifting 16ft lund aluminium fishing boat off trailer

    Have access to a chain block hoist on i-beam ,can a rope tied from bow to transom handles be used to lift it off the trailer safely? I ask cause there are no seats bolted on to hold the sides of the boat kind of flimsy along the sides in the middle.
  15. B

    1979 16ft lund aluminium boat bunker pushing up on floor bent rib

    Have a 79 lund 16ft aluminium basic tiller boat , on the bottom of the boat left side the bunker is pushing up the floor between 2nd and 3rd seats there are 2 ribs between the seats that are bent up . The stringers look ok from under boat but hard to tell if they are bent cause bunker in the...
  16. B

    Lifting 16ft lund aluminium fishing boat off trailer

    Have an old 16ft lund aluminium boat 1979-80 , want to get it off trailer to change rivets on hull . There is no motor or floors just the shell (basic tiller type boat) . Need advice on how to remove it from trailer and support it. Thanks in advance
Top