Search results

  1. WhiskeyNoise85

    1986 50 hp johnson with VRO delete

  2. WhiskeyNoise85

    1986 50 hp johnson with VRO delete

    Ok fellas.just a a friendly question Does it look like this motor is shaking to hard to you? Or it bc I have the tilt trim detached. Sometimes it coughs from a lean problem but i just haven't fixed That yet. Thanks for you opinions guys! Sorry I had to add the youtube link.the video was to...
  3. WhiskeyNoise85

    40 hp evinrude (year unknown) selectric shift model. HELP setting points and timing!

    SUPER LATE UPDATE! Did as lindy46 suggested. Motor fired right up!
  4. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Sorry for the SUPER late up update. but after all that checking and trouble shooting.it all came down to a broken ground connector on this piece the green one on top looks like its on there. But the male tab was actually broken.thank all tou guys for the responses.shes running like a top again.
  5. WhiskeyNoise85

    85 HP force motor. 2 questions!

    I see there are 6 wires on the trigger in what sequence do I test them for resistance?
  6. WhiskeyNoise85

    85 HP force motor. 2 questions!

    question this mod runs num 1 and 2 cylinder. Would the trigger be bad of.the num. 2 cylinder is.still working? Probably a dumb question... also ignore that the highlighted wire is supposed to.go to cylinder. 1 not the wire that's in it...
  7. WhiskeyNoise85

    85 HP force motor. 2 questions!

    I'll definitely check that bc the module is stupid expensive! 400 something thank you nordin!
  8. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Ok so update.. not getting fire to #1 sparkplug. ordering mudule.checked coil by switching wires and coil is fine.
  9. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Ok yes o have ran it with cowl off the past 3 times I've been out to diagnosis amd fix it. Same problem. I will be at dock soon to take pics and vidoes. Thanks again for all the reply well get it fixed!!!
  10. WhiskeyNoise85

    85 HP force motor. 2 questions!

    i do not have a rpm gauge.
  11. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Oh...yes it is ...SMH I'm not a smart man most days
  12. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Well what I mean by that is if I open the butterfly by hand I can achieve WOT. But I can also open then with the hand control...but I get bog. I'm going out there this after noon at 5 I will post a reply video. ALSO I do have a hole in my exhaust boot for sure! Could this be causing the...
  13. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Noooo that 1/2 half a gallon a mile sir.
  14. WhiskeyNoise85

    85 HP force motor. 2 questions!

    Hello again everyone. Ya boy whiskey needs some helps from the pros again! First off OMG do this motor usually drink a TON of gas??? I mean no exaggeration about 1/2 a gallon a mile at 10-11 mph. (The motor it on a 21 ft pontoon) Sorry this is gonna be a pretty long post but here goes. I'm a...
  15. WhiskeyNoise85

    40 hp evinrude (year unknown) selectric shift model. HELP setting points and timing!

    Thank you everyone who helped me with my problem. I had several problems causing the no spark on this motor. One severely corroded ground wire. (Causing over heating issue on main ground). Second was another corroded wire going to the vacuum kilswitch. And lastly my uncommon sense. I had to...
  16. WhiskeyNoise85

    1967 40 hp electshift rich/lean trouble shoot?

    Thanks for your comment. I will try that now. Freaking snow hand me on stop for a couple days.
  17. WhiskeyNoise85

    Lets play. I took it apart. Opps whats this piece?

    It came off the 67 40 hp evinrude lark 4. Now that you say that. It is the piece that goes to the choke from the cowling I think. It's about 12 inches long
  18. WhiskeyNoise85

    Lets play. I took it apart. Opps whats this piece?

  19. WhiskeyNoise85

    1967 40 hp electshift rich/lean trouble shoot?

    I dont believe so. I've never seen it choke automatically when I turn key. I know it would have to be on the setting automatic. Is there a thread you can recommend for adjustment
  20. WhiskeyNoise85

    1967 40 hp electshift rich/lean trouble shoot?

    Sorry just saw your request for the pic. I'm done with it tonight. But the jet is clean. So step one done right.?
Top