Search results

  1. J

    Leaking still after bellows replacement. Help please

    Thanks y’all for the help and advice!!! Probably going to do same. Try and get through season. I have slowed leak down a lot. By tightening the bolts. May try little more. My question is. With this leaking is water getting into the drive and bellows? As it seems to only be coming from bottom...
  2. J

    Leaking still after bellows replacement. Help please

    I just went out and inspected bolts on inside of transom and they are a little loose. I can turn them a few times with my 5/8 wrench. I’m guessing these don’t just come loose. I was able to get to the top two and bottom two bolts. And does sound a bit hollow tapping on very bottom of transom...
  3. J

    Leaking still after bellows replacement. Help please

    I just went out and inspected bolts on inside of transom and they are a little loose. I can turn them a few times with my 5/8 wrench. I’m guessing these don’t just come loose. I was able to get to the top two and bottom two bolts. And does sound a bit hollow tapping on very bottom of transom...
  4. J

    Leaking still after bellows replacement. Help please

    I’m hoping not as boat is in excellent shape. Is there any way it’s a seal between it. ??? I’m guessing I need to remove outdrive again and test with water in bildge again to get better look where it’s coming from. Before removing the engine. ? Any suggestions would be much appreciated.
  5. J

    Leaking still after bellows replacement. Help please

    Here is what I got from putting water in bildge. Not enough to barely touch bottom of oil pan
  6. J

    Leaking still after bellows replacement. Help please

    Can the shift bellow leak into bildge and where is location? I have replaced exhaust and drive bellows
  7. J

    Leaking still after bellows replacement. Help please

    I was one that was asking about the bellows few weeks back and the starter replacement. I finally got it back to the lake and still leaking. Was wondering about the shift cable bellow. Where it’s located and would it allow water in. I’m assuming it would have some sort of seal as it goes thru...
  8. J

    Leaking still after bellows replacement. Help please

    It’s the 4.3 omc cobra.
  9. J

    Leaking still after bellows replacement. Help please

    I have not test drilled yet, I however did not replace the shift cable bellow. Was this supposed to be changed. I was told not necessary! Also do you know where it goes or location? Thanks again
  10. J

    Leaking still after bellows replacement. Help please

    Had water coming in and replaced bellows and just took it out for first time after and still getting water in? Any other places water could be getting in? Seals or o rings etc....Posting a few pics and try posting video
  11. J

    Starter wiring please help

    Any idea of what it could be? It worked fine before I removed old starter. The old starter decided to start getting weak so I replaced it , looks like what was probably original giant starter lol. But key switch and starter worked before I took it off !!
  12. J

    Starter wiring please help

    It’s a 94 omc cobra 4.3
  13. J

    Starter wiring please help

    I have the two big red wires connected on big post. Yellow and red to the far right near block. And tiny purple wire on other side. Which is how old one was wired. But not getting anything
  14. J

    Starter wiring please help

    I got the new mini starter and can’t figure out wiring. I know the two big red wires go on the big post. I have a small purple wire and a red and yellow wire that’s together. Took pic of old wiring from old starter. Tried that and not getting power. Swapped the two small ones around and...
  15. J

    Starter help!!!!!! Omc cobra 4.3

    Do you know what size they are or where to get them. Tried few different gm starter bolts and none of them have been right .
  16. J

    Starter help!!!!!! Omc cobra 4.3

    Looks exactly like the one I pulled off mine. What size bolts did u have to get for new one?
  17. J

    Starter help!!!!!! Omc cobra 4.3

    Are you suppose to use smaller bolts in length. Starter is about 1/2 inch from snugging up when bolts are tight???? Any suggestions??? 4.3 omc cobra
  18. J

    Pulling outdrive question????!!!

    Any preferred brand transmission oil??
  19. J

    Pulling outdrive question????!!!

    Which side of bellows first on install? Transom side?
  20. J

    Pulling outdrive question????!!!

    Ok that’s a good tip. Thank you again. Have another question ..... where does shift cable bellow go? I didn’t see one when removed it????
Top