Search results

  1. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    With it in the first hole it is about level with the bottom of the boat.If you go to the second hole it will start bouncing at full throttle.I might have a tack at the shop .What should it be turning.Whatever it's turning it is plenty fast now.When I try the 25 on it it will probably be to much...
  2. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    I just did the water test with the motor raised 2 inches.Its running like a scalded dog now.I also tweaked the high speed jet on the carb that helped some also.Now it's scary fast Thanks everyone
  3. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

  4. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

  5. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    Here are pictures .I raised it 2 1/8 inches. Now with the pin in the first hole the front of the cavitation plate is slightly lower than the bottom of the hull.When adjusted all the way back it is slightly higher.Im going to try the second hole first..mI just redid the transom.
  6. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    Update got a welder making a bracket so I can raise motor .Im going to try that
  7. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    How do I adjust the high speed
  8. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    The boat transom is 16 inches.on the motor bottom of the mounting bracket to the top of the cavitation plate is 18.I also measured a 72 25hp johnson a 15 hp johnson and a9.5 hp johnson all appear to be 18 inches.I also measured a 30 hp johnson and it's 22.So I assume it is a short shaft
  9. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    N Ot sure how to adjust high speed
  10. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    I think it's a short shaft motor I'll get pictures tommorrow
  11. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    I set them at the factory settings .No I have not reset them.seems like motor is doing good great starting and idling for sure
  12. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    I have no idea.Its a cool looking prop
  13. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    The prop came on the motor.I bought it at an estate sale out of a barn SHE IS A GEM EVEN LOOKS GOOD
  14. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    The cav plate is 2 1/4 inches below the hull.Compression 112 both cylinders cold.Motor was trimmed all the way down
  15. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    Estate sale and yes the prop was on it
  16. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    Rated for 15 hp .I have run a 1972 25 hp on it a lot and it will move
  17. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    2 inches? Yes sir runs fantastic .cranks first pull and idles fantastic.Just got her running with your help.It will get fast but takes a while to get there.I was wondering if the low cav plate is plowing making it hard to get planed out
  18. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    Correction the motor is a 1962 model
  19. C

    1962 evinrude fastwin on a 1236 aluminum john boat motor height.

    The cavitation plate sets 2 inches below the boat bottom It seems to take to long to plane out .It has a 2 blade brass prop.Does the motor need raising
  20. C

    Cowling gasket on early 70s omcs

    Has anyone ever came up with a replacement for these .1976 40 hp evinrude
Top