Search results

  1. R

    murcury 650 timing belt replacment

    i Recently got hold of a 1974 murcury 650. It was tore down to bare block but I got all the parts bought all the parts it needed timing belt fuel line carb kits fuel pump diagram. Any ways the hub was off the flywheel. I turned #1 tdc lined the mark on fist gear with flat notch on distributor...
  2. R

    35hp evinrude has me puzzled

    hey folks. I been working on a 1983 35hp evinrude. Rebuilt carbs. New fuel pump. But it continues to bog down at full throttle. Engine has good compression. Can’t find no bad or broke wires. When I removed the fuel line from carb spinn it by starter. After priming fuel to the pump. It shoots out...
  3. R

    Evinrude motor mount bushings

    i Got a 1983 33hp evinrude 1 of the ruber bushing on motor mont is missing other side was loos but still there. What I’m asking is can these be taking on and off. With out taking the whole thing apart. If there’s a away I’ve not seen it yet
  4. R

    1956 evinrude 7.5

    im needing a part number for the rod bolt washers the bend flap has broken off. And need replacing. Wounder if a regular lock washer would work
  5. R

    Mixing 2 cycles oil

    this may be stupid but to get a accurate mix. Can one use digital scales to weigh oil
  6. R

    Old evinrude parts

    hello. Does any one know where I can purchase piston rings for a 1956 evinrude 7.5hp. I got ahold of 2 of these outboards.
  7. R

    Registering boat in North Carolina

    My dad bought a old Jon boat he put it on trailer and added a 6 hp outboard on problem is there’s no numbers on the boat anywhere no tags no stamps or marking it’s made of aluminum 12’ long. Is there a way to register this thing
  8. R

    Registering my boat

    hello everyone I Ben working on a boat that that’s been siting Sence 1994. The fellow I bought it off of hasn’t got the regesteration. I done a HIN search. It’s made in 1978 by bumble bee co also goes by middle Tennessee fiberglass. Stinger is the decalls on each side of the conslole. It’s a...
  9. R

    Getting the right impeller for my murcury

    Hello everyone I’m needing impeller rebuilt kit for a 1984 60hp murcury serial number 6462388 it’s hard to tell for sure which one I need. Is this the big foot engine
  10. R

    1978 mercury trigger

    Hello everyone I have 78 60 hp Mercury. The trigger wires corroded broke apart. What up and year will work on this engine.
  11. R

    90hp mariner rebiuld or not

    hello. i recently got a boat with a 90hp mariner which was bad and replaced it all ready. i took the mariner apart . and the middle piston skirt was busted off. didnt damage anything else. but all three cylinders has light scoring. would honing and new piston and rings fix this motor. the...
  12. R

    transom thicknes

    hey the boat im restoring. a 15 ft fiberglass bow rider it only had a 3/4 plywood transom. which held a 70 hp evenrude. most i have read usaly uses 2 3/4 plywood transom. but this would not give enough room for my cap to go back on. what im asking is 3/4 thick enough to hold a 70 hp evenrude
  13. R

    reinforcing the hull

    hello every one.im in the middle of replacing stringers and transom in my 15ft bowrider blazer iv noticed a crack under one stringer that goes all the way thru and a chisel hole i made while taking out the old stringers. anyways the bottom seems thin to me. im thinking about laying a sheet of...
  14. R

    1975 evenrude 70 hp prop

    im going to put a 70 hp even rude on a 17 ft bowrider. i know its to small but i havent got another motor. this boats weighs 1080 lb what size of prop should i use for best performance. it will be for riding and fishing with up to 4 adults.the prop thats on the engine now is broke so i want be...
  15. R

    1975 evinrude 70 hp on a 17 ft bowrider

    hello every one. i have 1971 thunderbird seminola 17 ft my brother in law got this boat first. it came with a 100hp johnson. he sold the motor. then i got the boat. i have another boat thats 15 ft with a 70 hp evenrude. but the boats bad. would this 70 hp evenrude push this big a boat. both...
Top