Search results

  1. J

    150 Johnson rod bearings snapping

    I was careful keeping them together but a few did get mixed up. I should have taken better care of them. Must I replace the snapping ones with new bearings? Thank you, john
  2. J

    150 Johnson rod bearings snapping

    When I tighten the rod bearings to 20 lbs and turn the crank, The bearings make a snapping sound when I turn the crank. I have tried aligning the caps many times with the same result. If the bolts are finger tight there is no snap. Any ideas. It ran With no noise, But had low compression...
  3. J

    Outdrive only moves prop at low rpms

    1988 4 Winns 350 omc . Engine revved up quickly while at about 3000 rpms, then would only move boat at low rpms. I would presume that the coupler let go, but anything else it could be? Verifying that I won't pull the motor for the wrong problem. Thank you, John
  4. J

    Edelbrock 1409 4v slows down after 3000 rpms

    Edelbrock Slows after 3000 rpms and sounds like it is bogging down. Carb clean inside with new accelerator pump. Any ideas? fuel pressure is 4 beginning accelleration, 3 during running to 3000 rpms. Too little fuel pressure ?Thank you, John
  5. J

    Ac Delco electronic dist timing procedure

    I have a 1999 Chevy 350 with AC Delco ignition. I could not find the timing plug so I set the timing to 10 degrees. I bought the timing plug to set base timing. When I plug in the timing plug, the timing still reads 10 degrees. I thought it would change using the plug. Am I correct or not...
  6. J

    Delco marine v8 timing

    If I want to change the timing on my Delco marine distributor, do I have to disable the dist with the shunt and start again? Thank you for any info you have. John
  7. J

    CDI ESA

    I have an AC Delco distributor in my 1988 4 Winns 350 boat. I have read where some people replace the esa module with one from CDI. What is the reason for changing, and what improvements can I expect? Thank you, John
  8. J

    Florida lakes and gators

    :confused: I have been to Florida a few times, and we are thinking of moving there in a few years. I enjoy fresh water much more than salt water. I have wondered if there are lakes that are free of gators so they are usable for fishing , swimming or water sports? If so, what areas are they...
  9. J

    Esa makes cables bind

    I have read many posts on the ESA system and problems and adjustments. Why does unplugging the ESA cause the outdrive cable to lock up??? Is there a relay/solenoid that allows the cable to be shifted or what??? Thank you, John
  10. J

    ESA adjustment

    I have a 1988 4 Winns 350 with an Ac Delco distributor and an ESA set up. I have adjusted the ESA as best as I can, but reverse is still giving me a problem. When it shifts into reverse, it stalls and comes out of gear into neutral hard. Would it be the lower cable on the engine bracket, or...
  11. J

    Yamaha wires

    Hi, does anyone know where I can buy ready made ignition wires for my 1989 Yamaha 115 hp? Whenever I have tried to make wires, it has turned out badly. Thank you, John:confused:
  12. J

    Wiring schematic

    To Don S., a few months ago, you supplied the motor half of a wiring diagram for a 1988 4 Winns 215 Sundowner. It has been very helpful. I believe you said it was from Clymer. Would you possibly have the forward half of the schematic available? Thank you in advance,you are an excellent...
  13. J

    Engine wiring diagram

    Hi, would anyone have an engine wiring schematic for a 1988 4 Winns 21.5 Sundowner 5.7L Thank you, John:facepalm: ?
  14. J

    GM marine engine

    :confused: Has anyone ever bought a GM marine engine through a GM dealer? Thank you, John
  15. J

    Oil drain hose

    I watched a video on winterizing, and the boat they worked on had a hose that was pulled out of the transom :confused: drain plug to drain the oil. I just bought a boat with a 5.7 1988 OMC. The engine is out and apart, ready for me to rebuild it, so now would be a good time to add this hose. Is...
  16. J

    Rpm change on 88 hp

    Hello, my son has a 1989 88 hp Evinrude. Sometimes, the engine will jump to full throttle when you ask it to, and bring him up on plane beautifully. Other times, it will go to about 2500 rpms for a few minutes ( it varies how long ) then it will go to full throttle by itself in a second. All the...
  17. J

    Windshield side wings

    Hi, I have a 1989 Sunbird 170 bow rider. The last owner cut down the side windows on the boat for some reason. Where could I buy either used side windows or the channel and glass/ lexan to make the windows myself? What is the difference between Lexan and plexiglass? Thank you, John:confused:
  18. J

    Wiring repair end

    I am adding trim and tilt to my 1989 88 hp Rude. I bought the t & t assy and the relay box on ebay. The relay box has a 5 wire round connector pigtail coming out of it. Can the other end of this plug be purchased, and where would have it? Thank you, John:confused:
  19. J

    Shift rod bolt 1989 88 hp

    I have a 1989 88 hp Evinrude that I want to replace the water pump on. Other outboards have a bolt that holds the top of the shift shaft on. On this motor, I see a pin in a fork that holds it together. How do I disconnect the shaft from the pivot?? Thank you, John
  20. J

    88 and 140 trim and tilt

    Hello, I have a 1981 Johnson 140 with trim and tilt. I just bought a 1989 Evinrude 88 with manual tilt. Can I take the trim and tilt off of the 140 and put it on the 88? Thank you, John:confused:
Top