Search results

  1. Idlespeedonly

    Metering rod help

    I have a 350 with vortec heads, clean quadrajet and edelbrock aluminum intake. Everything else is pretty much to stock spec. As soon as I hit 4000 rpm it starts to go lean. It pops pretty good, spark plugs look pretty good since I stay around 2500-3000 rpm anyways. The rods that are in it now...
  2. Idlespeedonly

    2007 Nissan Pathfinder transmission question

    Are there any Nissan tech's on here? I am having problems with the TCC. It is the RE5R05A transmission. Thanks.
  3. Idlespeedonly

    Brake controller

    Well I finally decided it was time to give up on the surge brakes. I have everything swapped over to electric drums now. I picked up a time delay controller, which I like way better than the old style. It works fairly well. But I have been reading up on the proportional style also. I think I...
  4. Idlespeedonly

    A bad day fishing is better than a good day at work?

    This poor guy was fishing on the Tennessee River. He was probably going around 50 when he hit a stump. The river is pretty nice when the water level is up, but it is pretty dangerous when they drop it. Luckily he didnt have a passenger with him when it happened, otherwise somebody might have...
  5. Idlespeedonly

    Correct routing for tilt/trim hydraulic lines??

    Excuse my artwork. They go between the transom and transom plate. There is a recess cast into the plate. You dont have to remove the lines to install the plate, since they go under it. The pic is the backside(the side that goes against the transom)
  6. Idlespeedonly

    transon repair advice

    My boat is an 88' Ebbtide. I was having problems last year with it taking on water, I believed it was because the transom was going bad due to the water leak and a hollow sound when tapping on it. I finally pulled the motor this weekend. Apparently my water leak was a combination of a leaking y...
  7. Idlespeedonly

    Intake for a vortec

    This fall I plan on replacing the transom on my boat, and while I have it tore apart I am going to replace the tired old engine. I picked up a short block 350 yesterday for free. So my question is what is the most common dual plane, spread bore intake being used. This is just a standard build...
  8. Idlespeedonly

    Threads I comment on notification

    Before the upgrade any thread I would comment on was marked by a little icon. Now this little icon isnt there anymore. How can I get it back? Thanks for any help.
  9. Idlespeedonly

    For all the RIB owners

    This is a video I saw this morning. I dont really know what I would do, I would have probably hit him in the nose or something. On second thought I would probably never put myself in that situation. https://www.youtube.com/watch?v=SCUc3U8WVMo
  10. Idlespeedonly

    Help with hatch sealing

    My front hatch has been leaking for quite sometime. So I am going to reseal it. The factory seal is a rubber bead/moulding that looks like it was glued in. I guess over the years is has shrunk causing the leak. What would be the best material to use to fill in the gap and get it sealed back up...
  11. Idlespeedonly

    Name color and rank

    Why are the names of a few on here in green instead of blue? And second, why dont they have a rank, I.E. petty officer, captain. Thanks
  12. Idlespeedonly

    2000 parti kraft rough estimate of value

    Re: 2000 parti kraft rough estimate of value One more.
  13. Idlespeedonly

    2000 parti kraft rough estimate of value

    I am looking at a 2000 Parti-Kraft made by Godfrey Marine. It is an 18 footer with a 50 horse 4 stroke Mercury. All I have right now are some pictures. It looks like he is wanting 4500 for it. It looks to be in fair condition by the pictures.I am planning on seeing it within a couple of days. To...
  14. Idlespeedonly

    Catastrophic engine failure...

    Re: Catastrophic engine failure... Use these fibrous discs not an abrasive type. These little things are like magic.
  15. Idlespeedonly

    Removing bottom paint

    My boat is a freswater fiberglass boat that used to stay in the water, so the po put on some bottom paint. I am not at all familiar with bottom paint. The stuff that is on there is extremely chalky. If you just brush up against it whatever touched it is instantly black. And it is very difficult...
  16. Idlespeedonly

    my next boat

    I thought i would post this. http://www.youtube.com/watch?v=KMsUXUQx-XI&NR=1&feature=endscreen
  17. Idlespeedonly

    SHT worth watching (sorry, already been posted)

    This is on CNN. There reactions are priceless. http://www.cnn.com/video/?hpt=hp_c3#/video/us/2012/09/05/vo-boaters-thrown-in-accident.lake-tv-mylaketv
  18. Idlespeedonly

    SHT by somebody else.

    Well our family witnessed a SHT by somebody else. We were at a lake in Lexington Tn. this weekend. We take our jet skis here often cause it is close. EDIT They are always performing their "stunts" within 30 yards from shore and about 20 yards from a swimming area. Well this time they had about a...
  19. Idlespeedonly

    Shift rod over looked for shifting problems.

    Re: Shift rod over looked for shifting problems. Item 46 and 47 are what you are looking to replace. They will most likely come in a complete seal kit. The only thing pressed in is the bronze bushing.
  20. Idlespeedonly

    OMC 4.3L Timing Chain

    Re: OMC 4.3L Timing Chain The one on the right is a leaf style chain. It is just a basic stock type chain. Probably what the one from napa looked like. The one on the left is probably what the one looked like that failed, generally called a roller. Either one will work fine. The roller is...
Top