Search results

  1. W

    Trim limit issue

    Hello i have a 1983 ArrowGlass tri-hull with a 77 Gm i6 alpha 1 drive. my problem is i had to replace both the trim sender and limit switch i got the sender working for the gauge but once i have the limit switch working i can push the up button...
  2. W

    Trim limit issue

    Hello i have a 1983 ArrowGlass tri-hull with a 77 Gm i6 alpha 1 drive. my problem is i had to replace both the trim sender and limit switch i got the sender working for the gauge but once i have the limit switch working i can push the up button and it will go all up but nothing if i push the...
  3. W

    trim button issue

    well have been spending time out on the lake she runs very well after fixing a slight leak i just found. but have a question about the 3 button trim switch. the in button works fine and the up/in+up button works when both are pushed,but when i push just the up button nothing happen?? i did try...
  4. W

    3 button trim switch issue??

    well after the down time in winter was happy to get out in water. well went home replaced bellowsdo to unknown issue still confused about but. main issue went to adjust the trim limit switch and had key on and turned the switch well?? nothing would happen and on the 3 button the in will work the...
  5. W

    water in bilge

    well was not a bad summer finally got the boat running and out in the water she plains very good even for sitting lower in the aft with a bigger engine. but have found i am getting some water in the bilge and i have no idea where.. the bilge area is closed off from any other part of the boat i...
  6. W

    oil change SD

    well it has been a while and the boat is finally ready to go in the water after all the flooding we have had around here the lake is finally open. but now i want to change the oil in my stern drive i have looked all over and haven't found the way i guess i have to do it. The stern is a MR 1...
  7. W

    will not run

    hi all well its about time to get here in the water went to fire up the motor, inline 6 250ci 165hp the motor is a 1973. well it cranks but will not fire even if i put gas down the carb. i pulled 1 of the plugs to check for a spark and it did turn over and seemed like it wanted to run with the...
  8. W

    titl trim control?

    I know this is a dumb question but i have traced the wires for my TnT after all the help i got here but the one thing that gets me is the 3 bottum control i noticed that the up bottum will only work if you push the up/out button but you can push the bottum by its self and it works? is that right?
  9. W

    trailer an boat question?

    Well i am trying to figure out how to do this but when i got my boat there was no motor in her and i noticed that the hull was only being held on the trailer from the bunk boards or runners there wasnt a single part of the boat on the wheels i lowered both bunk boards down one side at a time...
  10. W

    trim wires?

    i am sure i am being a pain the the bellows but i am rewireing the trim light switch and the trim indicator sender unit and have looked at both the wires and the wire colors are both black and i am not sure where to run them i know in one place it says the purple/white wire goes to the trim...
  11. W

    stern drive?

    i have looked and for some reason can not find any place where i can look up what type of stern drive i have the number on the side is 4002876 the top cap is square with an eye on top.
  12. W

    marine SAE J1171 trim pump HELP

    i would like to know if some one might be able to find a wiring diagram for the Marine SAE J1171 trim pump i have looked online and also in the silco book and can not find mine in the book the pump came off a 1981 boat with a trim sender mounted above the transum...
  13. W

    Merc 250 cci questoin

    Hi all well it has been a while since i have posted but need a question answered if i could please on my engines wiring harness there is a white wire going from the coil to smoe place els and in the book it says it is a resistance wire? when the motor is running the wire gets hot is this wire...
  14. W

    engine preoblems?

    it has been a while since i have posted anything but i have finally set the engine stringer mount and then droped the motor in bolted up the back transom mounts and started to try and allinge the motor and had to drop the adjuster bolt all the way down so i pulled the motor back out and added a...
  15. W

    prop Info please

    Hi again all well the arrow-glass is almost out of dry dock now just have to figure out how to mount the motor mount down to the hull but the biggest question is what prop do i use since i dont have one any more the motor and boat specs are as follows.. 1980-81 arrow-glass cheetha 17'5 try-hull...
  16. W

    hull cracks??

    Hello again well have been doing some good work on the boat foam in all new stringers and floor. but what i have a question about is there are cracks on the bottom of the hull she is a try-hull i was woundering if they would be caused do to the fact that the old stringers where gone as in wood...
  17. W

    manifold help?

    i have a merc 165hp inline 6 and removed the side plates from the manifold and found alot of rust inside of it how to clean that out and get better water flow??
  18. W

    placing stringers

    i rewatched Frissco's vid's and see where he placed foam under the stringers before glueing them in should that be done also on a try-hull?? i noticed that on the old stringers there is no spacers or anything? Also whats the best way to fix a small hole in the hull looks more like a nail hole?
  19. W

    HELP on small stringer

    i have run into a problem on my try, she has 2 stringers 6" tall and i have made new ones out of 2 15/32" 3layor ply. but the problem i am now running into is there is a small stringer that runs down the center of the Keel and its only 1 1/2" maybe 2" thick but 3" tall? is this a keel structural...
  20. W

    port holes?

    on the arowglass i am redoing she has 2 drain holes on the port side for the cooler's or storage under the 2 bow seats to drain out before i replace the foam in the keel and the deck or floor i am planing on running new drain lines to go to the bildge area so what would be the best way to cover...
Top