Search results

  1. LonLB

    Boat restoration. Foam or no foam??

    Re: Restoration - foam or no foam??? Re: Restoration - foam or no foam??? Read this. It's a bit of an eye opener. This boat didn't hit anything or forget their plug or anything else. This happend from WAVE action. http://www.ohiobass.org/StateTournaments/Erie/Erie.htm Flotation makes...
  2. LonLB

    Sea Nymph 17' Deep V.

    gunnel step pads gunnel step pads Anyone know a source to buy these new??
  3. LonLB

    Sea Nymph 17' Deep V.

    Rivets that look "bucked" Rivets that look "bucked" Found a Rivet that will work for me. I wanted a factory appearance since they will be on the outside of the boat. The best part, after searching for something I wanted/needed I found Shaveable rivets. And realized, hey, I have a bag of those...
  4. LonLB

    Sea Nymph 17' Deep V.

    Re: Trolling motor mount Re: Trolling motor mount Just a mock-up of what I was thinking. The gauges will go on the large flat panel above the console. I've got some acrylic I'll make for a "gauge panel" and keep them over closer to the transom. Then mount the electronics on top of the...
  5. LonLB

    Sea Nymph 17' Deep V.

    Re: Trolling motor mount Re: Trolling motor mount Also built a trolling motor pedal recessed tray. Still looks rough, but it'll be carpeted along with the rest of the deck. I'll install a couple drains too.
  6. LonLB

    Sea Nymph 17' Deep V.

    Re: Trolling motor mount Re: Trolling motor mount I've been working on the boat SLOWLY but steadily. Been doing a few small things, and fixing, or re-doing things that were already done. Just to clean them up. First the start of my rear transom/splashwell/rear deck area. Here is my tiller...
  7. LonLB

    Aluminum v hull restoration, how-to's? Lmuss53's 171CC Sea Nymph Striper

    Re: Aluminum v hull restoration, how-to's? Lmuss53's 171CC Sea Nymph Striper Ya, my boat had the same 2" transom. Kind of an oddball size for the DIY'er. I replaced it with 1.5". It works for the Starcraft guys, it should work for us. The start of my boat's transom area/splashwell...
  8. LonLB

    sea nymph restoration

    Re: sea nymph restoration Here like this. Exactly what I meant. (not my boat)
  9. LonLB

    Rivets?

    Hopefully this isn't against the rules... I know there are some Starcraft guys in the fine state of MI. My question is do any of you guys have the tools and ability to install solid rivets? Do you know of someone who does? I want to remove my trim channel on the side of the boat, and then...
  10. LonLB

    Sea Nymph 17' Deep V.

    Re: Trolling motor mount Re: Trolling motor mount Ok so this way keeps it off the aluminum trim. But, when folded the bracket, and motor will be hanging off the side of the boat. If I move it over, so that the mount, and motor will run down the gunnell, it would be like this. And this
  11. LonLB

    Sea Nymph 17' Deep V.

    Trolling motor mount Trolling motor mount So I had a Minn Kota Powerdrive but it was 12v 54lb thrust, 48" shaft. Traded it for a 24v 67lb thrust Motorguide with 60" shaft. Issue is though, compared to the powerdrive the mount is HUGE. To fit on the bow, and NOT be on top of that aluminum...
  12. LonLB

    Will a 100hp tilt/trim work on a 70hp engine??

    Can I fit a xp100 tilt/trim to a 70hp Evinrude??
  13. LonLB

    Sea Nymph 17' Deep V.

    trailer. trailer. Got the boat on the other trailer. Not a perfect fit, but they never are. Had to cut the side guide on bunks off, and still need to adjust the bunks. Oddly enough the wood on the bunks was like new so w/new carpet I'll reuse it. Some sandblasting, paint/wheels etc, plus some...
  14. LonLB

    Sea Nymph 17' Deep V.

    Re: Front deck and a few hatch questions. Re: Front deck and a few hatch questions. ZERO motivation today to do anything but watch movies. Had a late night last night with the family around the fire, then a movie. Finally I got restless enough that I had to do something. So I made another...
  15. LonLB

    Sea Nymph 17' Deep V.

    Trailers. Trailers. Need to make a trailer decision soon. Keep the one I have or switch to another trailer. Switching will cost nothing as my neighbor will trade even up. Current Trailer. The Other Trailer. I'll have the one I use sand blasted. The current trailer has an advantage in...
  16. LonLB

    Renew the finish of old pedestal bases?

    Probably a dumb question, but I have several used pedestal bases. Anyone have tips for making these look new??
  17. LonLB

    Jet/Jet Star questions.

    I'm currently working on a project, but 'might' look into getting another boat when this one is done. I'm curious, how shallow of water is a Jet/Jet Star capable of going through?
  18. LonLB

    Sea Nymph 17' Deep V.

    New splash well. New splash well. I got to work on my splash well last night, and this morning. It will be much, much smaller. I'm also mounting it lower than it was. Then I'll build a small deck over all of it except the well itself. The framing for the deck will add the support that I lost...
  19. LonLB

    Tilt Trim Interchangability

    I have a 73 65hp Johnson. I would like to add power trim/tilt to it this summer. I would like to know what other trim and tilt units will interchange. I assume all the 3 cyl engines 60-75hp will interchange. Will any others? I've searched a bunch and not come up with answers. In case it...
  20. LonLB

    A repair manual question.

    I need to get a Repair manual. Engine is a 73' 65HP Johnson. I could by a Seloc, which I've never looked at before. They cover multiple engine sizes. OR, I could by a 70HP OMC service manual from a 74' This engine is VERY similar to the 73' 65hp. Which one should I get. Will I have lots of...
Top