Search results

  1. beverly

    '53 Super Fastwin......it wants to run. It really does! EDIT: IT'S ALIVE

    Re: '53 Super Fastwin......it wants to run. It really does! Re: '53 Super Fastwin......it wants to run. It really does! Food for Thought If that diagram is right then your primer bulb would never get hard/stiff and you will end up priming/pumping fuel gas into by-pass plate that shows a...
  2. beverly

    '53 Super Fastwin......it wants to run. It really does! EDIT: IT'S ALIVE

    Re: '53 Super Fastwin......it wants to run. It really does! Re: '53 Super Fastwin......it wants to run. It really does! I found this while searching around cause I'm going to be heading in your direction if I can't make this Mikuni Fuel Pump work.
  3. beverly

    Tuning Up - 1975 Johnson Sea-Horse 9.9HP

    The motor is a 1975 Johnson Seahorse 9.9HP. I did a tune up on the points and spark plugs, point contacts and carburetor alignment. Under the flywheel looks like this Coil packs attached on the side of the engine. I wanna talk about the coils and sparks that zaps. So far the spark plugs have...
  4. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle That rod was bent when I got the 15 so I bent it more to idle (Trial and Error) but it only opened up so far. It seems the Armature Plate isn't moving far enough to open the the throttle butterfly wide open. This picture shows the Armature Plate...
  5. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle
  6. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle
  7. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle A video treat, well still the same problem.
  8. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle I'll be. I didn't notice the two holes until now. It was always in the furthest hole even on the cam follower lever. So that mark on the on the cam, is that idle or STOP.
  9. beverly

    Fuel line question on 1953 Evinrude fastwin 15hp

    Re: Fuel line question on 1953 Evinrude fastwin 15hp Mine looks like this if you can see it. This seems to work but I'm currently experiencing a problem with my outboard that has this setup. Just make sure the gas tank isn't a a few feet below the motor as I get running problems.
  10. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle Here is some more pictures with a different shades of backgrounds
  11. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle Here some more pictures of that small needle
  12. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Re: 1953/54 Evinrude Fastwin 15HP - Won't Idle Some more picture added
  13. beverly

    1953/54 Evinrude Fastwin 15HP - Won't Idle

    Engine starts and runs mid (Start) to high idle (WOT) fine but when I slow it down anything at or below shift it coughs and coughs then dies. Fuel line has been modified to run on a single line with a after market fuel pump (diaphragm) can be found HERE <=CLICK Cylinder Compression - Both...
  14. beverly

    What if... Conversion 15HP=>9.9HP / 9.9HP=>15HP ...I just turn the carb. down

    Hi, I'm from Ontario I heard a story from a friend of what people use to do to a 15HP, is to convert the carb to a 9.9HP to be legal with not having to register the boat. I know you can convert a 9.9HP to a 15HP by changing the carb. I also know you can also convert a 15HP to a 9.9HP just by...
  15. beverly

    would this fit? 50's -> 80's Evinrude prop

    I own a 1985 Evinrude 8hp with this prop and as a temp replacement while i get this one repaired Would this one fit? Its from the 1950's (56,57) Evinrude or Jonson Same shaft dimension all except 2 blade (8" x 8.5P) vs 3 blades (8.5" x 9P). The back is what I can't see or find out what...
  16. beverly

    would this fit? 50's -> 80's Evinrude prop

    I own a 1985 Evinrude 8hp with this prop and as a temp replacement while i get this one repaired Would this one fit? Its from the 1950's (56,57) Evinrude or Jonson Same shaft dimension all except 2 blade (8" x 8.5P) vs 3 blades (8.5" x 9P). The back is what I can't see or find out what...
  17. beverly

    1985 Evinrude 8hp - T

    Picked up a boat (13 foot holy aluminum), motor (1982 Evinrude 8hp) and trailer (homemade 150 LBS busted lights). Note. First time on the water for 4 hours (fishing test). Mid throttle it would misfire but after it warmed up you could almost go WOT. At WOT the engine hesitates (kinda misfire...
  18. beverly

    Diff brands of props? - 1982 Evinrude 8Hp

    I have a (new) 1982 Evinrude 8Hp and considering buy and repairing my other prop. As for buying one. theres different brands which gets confusing for a newb Solas Amita 3, 3-Blade Aluminum Prop #2011-085-09 Michigan Wheel Michigan Match 012032 Aluminum Boat Propeller Quicksilver Black Diamond...
Top