The iboats forum moderators are excited to announce that at this time it appears the iboats forums posting pictures function is working once again. Though we cannot promise for how long, we're hoping for indefinitely.
Is there a good-yet inexpensive- trolling motor bracket (or way to do it) that would allow me to mount a transom mount trolling motor, to the transom area or stern of my 14' Bayliner capri bowrider? the transom does not allow room next to my outboard for a clamp on type, and my budget doesn't...
How hot is an '85 force 50 supposed to run? I heard the t-stat is a 120 but ive never changed it. The water coming out of my engine is only at 125 but the motor seems pretty hot. No problems i just want to know. It pumps water very well.
I found that my 50hp force has a cracked/torn fuel pump diaphram. I ordered and recieved the new one and am wondering should there be any RTV type sealant used on the gasket? or does it go on dry?
After checking my ign electrical as to why my 50hp Force wouldn't idle good, I tested the fuel pressure. Primed good, but no flow when cranking. i pulled the fuel pump cover and saw the diaphragm was torn! I am ordering new parts and I was wondering if when changing the diaphragm, it is...
What do you guys think is the best location for the Bilge pump through hull fitting? I am putting a 500gph electric Bilge pump on my 15ft Bayliner Capri-outboard- and was thinking the Starboard side so I can see if it is working, or maybe into the splashwell so I don't actually have to drill...
There seems to be a seep hole next to a bolt on my upper gear housing ( pic attached) that oil comes out of slowly (into the water) when I run the motor in a trash can. I am wondering what the purpose is for this since I cant find anything about it. it looks like a 1/16th hole drilled upward...
Anyone SURE of the proper fuel mixture for my '85 force 50? I am mixing my fuel at 50:1 ratio per my clymer shop manual. and it seems to be running rich. It sat for several years before i got it. I cleaned the tank/carb/and fuel line. Starts right up and doesn't overheat, but seems to smoke alot...
I have been running my Force 50 in a 33 gal trash can full of water in my backyard, and it seems to pump water just fine-i can see it in the bypass tube and out the exh. and it stays pretty cool. When I hook it up to muffs/ my hose I don't see any water in the bypass tube and none comes out of...
I am almost done restoring the interior of an 85 bayliner capri, and the hull is in perfect shape including gel coat and of course it is white, with the exception of some small stains on top of the gunwales and in the aft nonskid area by the splashwell(outboard) that look to be rust from...
I am inthe finish stages of restoring an 85 Bayliner capri and am wrapping all the 3/8ths ply for the interior side paneling with1" foam and marine vinyl.
I cannot seem to fold the vinyl over to staple it without a large pointy "fold" in the corners. I'm doing it kinda like a Xmas present but...
I am getting ready to reconstruct the interior of my 85 Bayliner capri. I am planning on using 1/2" exterior ply for the side panels wrapped w/ 1" foam and marine vinyl from Joanne's. I would like to find out what some of you guys have used for sealing the ply to prevent rot. I have heard...
What type of rivets are used to put the rubrail/cap back on a Bayliner?:confused: galv,alum,s/s ? How long also? I am getting ready to pop the top on my bayliner capri to replace the transom and want to make sure i have them ahead of time. Also how hard is it to reuse the rubber, it seems pretty...
Bought a 1985 Bayliner w force 50, battery is bad (not marine either) so been looking for a replacement. I found Diehard has a 550 cca marine deep cycle batt for $69.99. Is this sufficient? my boat does not have a stereo or other electronics (yet).
Hi all,
First off Sorry for the long post. I am new to boats and purchased a 14' 1985 Bayliner with a Force 50 2 cyl outboard. I was a little intimidated being a first boat owner and knowing the boat needed 'some work'. After joining this site and following threads, I have gotten so much...
I am in the middle of doing a deck repair/replacement on my 85 bayliner. I thought it would be cool and useful to get a hatch cover for the battery compartment, the center seat used to cover it. I am eliminating that seat to make it easier to move around in the boat. I ordered a tempress hatch...
I am in the process of putting a new deck on my 85 Bayliner Capri. I already glassed in new stringers/supports. I am using polyester resin/6oz cloth. Is it advised that the new deck-5/8 sanded exterior ply-be sanded or roughed up to increase poly bond to the new plywood as it is a very smooth...
I am getting ready to put down a new deck on my bayliner capri using a good exterior 5/8 sanded ply. I am new to fiberglassing and trying to do this on a budget. I will be using Polyester resin/fiberglass. Is it nesessary or does sanding or 'roughing up' the ply help the glass/resin to bond? is...
I picked up an 85 Bayliner Capri Bowrider that I have removed the damaged deck areas and am planning to put down new stringers,a ply deck and fiberglass. The bilge area(i assume it is called)under the bow deck, is compartmentalized-cut off- from the battery area under the main seats. Is it...
Hello all-
I just picked up my first 'project' boat, an 85 Bayliner Capri Bowrider w/ 50hp Force. It is a "fixer upper" (haha) with a near perfect hull and motor. All else will need to be redone by me including upholstery, seats, deck, carpet ect. So I know this being my first boat I will have...
