Search results

  1. E

    7.4 not running right

    I have a 1990 sea ray sundancer in which over the past 7-8 years I’ve completely rebuilt…new interior, new motor, bravo 3 drive…yesterday I finally got to splash her for the first time inn8 years or so. I put $80 in fresh gas in her, it was empty before, it started fine with 2 pumps of the...
  2. E

    Winterization

    I know I’m gonna get some flack about this but here goes. I got my 1990 sea ray sundancer back up and running after a 5 year hibernation… I am at the point of winterization, it’s a 7.4 big block motor, I removed the bravo 3 drive. Where are all the points I need to drain the water from the...
  3. E

    Bravo 3

    I have been trying to chase a, I guess you can call it hard shifting in my bravo three. When I reinstalled the drive, I noticed that the drive was in gear. And then disconnected the shift cable from the motor mount and manually tried to shift it with a pair of vise grips and it would just not...
  4. E

    Window ?

    I am in the process of restoring my 1990 sea ray sundancer and I need to replace my pieces of the side windows that the glass itself sits/slides on, it’s located all the way from the front to the back of the window, as you can see in the pictures mine are dry rotted & cracked/broken.anyone know...
  5. E

    Shift cable ?

    OK as many of you may know I put a new motor in my 1990 Sea ray Sundancer, 7.4 L.. I have had the outdrive sit dormant for the past 4 to 5 years. I installed the outdrive went to hook up my shift cable and I adjusted it according to the manual and my shifter was extremely hard to go into gear so...
  6. E

    Trim

    Ok I finally got my 1990 sundancer up and running after being dormant for the past 5 years…when I parked it the drive operated just fine. Now that I got a new motor in it and hooked up my bravo three outdrive, it will trim down fine but it won’t go up and when I hit the tilt switch it just...
  7. E

    Drive oil

    Can I use any 75w90 gear oil in my bravo 3 drive?
  8. E

    Shift cable?

    I just got done replacing all my bellows along with my shift cable. Am I ok to assume I can just go ahead and install my drive and do my cable adjustment at the motor? It’s a 1990 sea ray sundancer with the 7.4/ bravo 3 drive.
  9. E

    Bellows installation took

    Anyone know what this particular tool is called? I’m in the process of installing new oem bellows in my 90 sundancer with a bravo 3…
  10. E

    Bellows ?

    I recently purchased a quicksilver bello’s kit to replace the old worn out bellows on my 1990 Siri Sundancer. I understand the big bellows are for the U joints in the shift Bellows, but I guess my question is why do I have 2 exhaust bellows in the picture?
  11. E

    Question

    Is there a trick to installing this sleeve onto the exhaust bellows? I’ll be changing them all out very soon & just don’t want not be prepared is all.
  12. E

    Mechanic needed

    OK I am at my wits end with this thing… I have a 1990 Sea Ray Sundancer that I just put a freshened up 7.4 454 motor in it. I also purchased a Holley 750 double pumper carburetor to put on it. I was able to get it running but while running for some reason it seemed to fouled the plugs out with...
  13. E

    Quicksilver ?

    Ok I just got my quicksilver bellows transom repair kit. I notice that the gimbal bearing that came with it is a sealed unit, non grease able. I thought the quicksilver kit came with a greaseabke bearing? I bought it from Amazon
  14. E

    Fuel pressure

    When adjusting fuel pressure to the carburetor, do you go by the number when the Motor is running, or after you shut it off in the number that it is at at that point because while my motor is running I am getting 8 1/2 to 9 pounds of pressure, as soon as I turn it off the needle goes to you...
  15. E

    Hard starting

    As some of you may know I’ve been trying to track down my hard starting issue I’m having with my 1990 sea ray with the 7.4 big block. I recently installed a new Holley 4150, 750 double pumper carburetor on it and in order to get it to start I have to keep turning the key on and on and on… I’m...
  16. E

    Plugs fouling

    Okay as some of you may know I just got done putting a new carburetor on my 1990 7.4 454 motor. I know most of you are going to give me flack for not having a marine carburetor on here but I couldn’t pass a good deal down so I picked this one up to throw on here and see what it would do. Why...
  17. E

    Fuel pump/carburetor

    OK bear with me here guys, I just got done doing a swap on my 1990 sea Ray Sundancer with the 7.4 454 big block motor. I also attempted to rebuild my Quadra jet carburetor and I must’ve messed something up so I went ahead and purchased a new Holley750 double pumper carburetor for it and I guess...
  18. E

    Carb question

    Anybody have any tips on getting these pesky J tubes taken out of these holly carburetors so I can install new ones? The ones that I have are broken off
  19. E

    Starting problems.

    OK here’s my dilemma. I just got done putting a motor in my 1990 sea ray Sundancer, it is a 7.4 454 motor. If I dump gas in the carburetor it will fire up momentarily and then die of course, but for some reason I am maintaining 8 pounds of pressure at my carburetor from the fuel pump but it...
  20. E

    What are these?

    As some of you may know, I am in the process of putting a new motor in my 1990 see race on dancer with a seven. 4 L big black Chevy. Does anybody have any idea what these parts are in the pictures and where they would go?
Top