Search results

  1. Wave34

    Waste tank cover removal

    If it's 5200, the cover needs to be destroyed?
  2. Wave34

    Waste tank cover removal

    Yep, I need to remove that cover to clean the level floats that are stuck. The cover seems to be glued or whatever, but I can't turn it. I tried with a strap wrench, but had to stop before breaking the plastic tabs. Any way to soften the glue or silicone?
  3. Wave34

    Which waterproof spray for cover

    I use a product made for camping canva tents and it works very well and a lot less expansive ($50 CND per gallon) Instructions say to brush the product, but I remove the roof from the boat, and after washing it, and drying it overnight, I use a spray bottle (pump type) and soak the canva. Works...
  4. Wave34

    Inaccurate fuel gauge?

    Does that mean that you use the analog output of the sensor to your gauge, and not the NMEA2000 ? I have an older Garmin GPS, and Garmin say that I need to upgrade the firmware to be able to accept the fuel flow sensor on NMEA2000.
  5. Wave34

    Inaccurate fuel gauge?

    Nola Mike; You say: ' to account for the attitude of the tank'. It may be just that, the angle of the tank creating a bad reading at the level sensor. On my boat, when stopped, the fuel tank is not level, in leans down at the front, and my gauge is at the back, so I read always lower than...
  6. Wave34

    Stern drive rising up on its own

    Check the breaker behind the engine near the distributor. It has a red button.
  7. Wave34

    Trailer Guide Ons DIY?

    On my trailer, I tried first the vertical posts uprights. In theory, they are perfect to center the boat. The reality I found, is that since the boat is wider in the center and the posts are at the back, they can't be adjusted to touch the boat because the boat won't pass between them (middle...
  8. Wave34

    Engine overheating

    Problem found! On the raw water pump (Volvo, on the crank pulley), there is a oil seal that keeps the water from flooding the bearing, and keep air out so the impeller can create suction. From what I read, when that oil seal fails, water goes out in the bearing. Only a few times water get...
  9. Wave34

    Outdrive trim pump, where is the power source

    Update on my trim motor repair; I took the boat out for the first time since my repair. The motor was working fine in my driveway. On the water, it was working fine at first, then, after forcing at the end of the down travel, it stopped working... for a while, then worked again. The only thing...
  10. Wave34

    Engine overheating

    Chaparral 260 Volvo Penta 5.7Gi-D / Duoprop SP-SM I can't find the problem. The boat has been working fine last year. I winterized it like usual, and removed the outdrive for inspection and to change an oil seal. I reassembled everything this spring, and went last week end for the first ride...
  11. Wave34

    Electric windlass wiring problem

    Chaparral Signature 260 2004 Hi all. On my boat with electric windlass, I have a 50A windlass breaker behind the battery switch door, PLUS a 50A glass fuse under the helm near the buss bars. The 12V from the fuse goes to the anchor switch UP-DOWN. Everything was working fine before I touched...
  12. Wave34

    SX outdrive stuck or was now broke :(

    What keeps your gear from being pulled is the inner race of the bearing #10. It is press fit, but not that hard. On a bench, only a hammer and tube is enough to make the gear move. So, try to find a way to pull on the gear, or pry, and it should go out.
  13. Wave34

    tilt trim system

    I had a similar problem as you have. look at this, and to post #9 for your answer. https://forums.iboats.com/threads/outdrive-trim-pump-where-is-the-power-source.740671/ On mine, the problem was caused by a seized trim motor, which was full of water and rust. After cleaning and lube, it worked...
  14. Wave34

    Refrigerator 1.9cu ac/dc

    You didn't say if the problem was on AC or DC or both. On my boat, the fridge was working fine on AC power, but on DC, it started, then after 20s it stopped. The problem was 2 things. 1. the breaker was resistive and dropping voltage 2. the ground wire was resistive also and dropping voltage...
  15. Wave34

    Shimming Bearing Cover DP-SM / SX-M

    I was in the same 'boat' as you... I had stripped threads but didn't want the expanse and trouble of shimming a new cover. I cleaned and degreased the cover, applied JB Weld around the circumference, and tap with new treads. It seems solid. I did that a month ago, so didn't try it yet, but I'm...
  16. Wave34

    Charging voltage drop with diode isolator

    Thanks for the info. Yes the 'excite' is internal and I won't modify the alternator. The Argo isolator 'FET' semiconductor seems to be a good solution, with a maximum of 0.1V drop at high current, and less drop at low charging rate. Either that or the ACR, but both seem to solve my problem...
  17. Wave34

    Charging voltage drop with diode isolator

    It makes sense. I just found on internet the manual on my diode isolator, and they say to cut the B+ wire and pass another wire to the isolator. I'm surprised that my boat didn't come already equipped like that from Chaparral...
  18. Wave34

    Charging voltage drop with diode isolator

    Yes the orange is tapped off at your blue arrow, and the other end seems to go to the relay box. The Red you are pointing to has one end to the ALT output (new wire), but the other end is buried in the wire loom.
  19. Wave34

    Charging voltage drop with diode isolator

    Jim, those smart chargers, are they only on 120V? Or they can be installed between the alternator and the batteries, in place of the isolator? It seems that a ACR is installed on newer boats. If I replace my diode isolator with a ACR, I will gain 0.7 volts when I'm driving the boat, would...
  20. Wave34

    Charging voltage drop with diode isolator

    alldodge, my alternator output seems to go to the relay box. Take a look at my other post, I have some pictures. https://forums.iboats.com/threads/alternator-b-wire-vs-relay-box-volvo-penta.742318/ but it's possible that after a relay it goes to the isolator. Here is a drawing I made of what 'I...
Top