Search results

  1. L

    Mercruiser 4.3L lift points

    The water is warm and seems too slow to come out while running motor. Any solution?
  2. L

    Power tilt failed to pull the outdrive up

    I have solved this issue and I found the connector to hydraulic pump was loosen and it works after I put it back. thank you a lot
  3. L

    Power tilt failed to pull the outdrive up

    Yesterday I found that my power tilt failed to push my outdrive up. But it can make the outdrive down. Which part should be replaced? My engine is Mercruiser 2.5L,120HP, year is 1989. Thank you
  4. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    The power tilt cannot work correctly. It can let outdrive down but cannot pull the outdrive up. Which part is bad?
  5. L

    Mercruiser 4.3L lift points

    I am concerned that the old alignment bar was damaged and it will damage the coupler if I apply to do the alignment job. so I bought one. But the new alignment bar cannot go through the gimmbal bearing. I am trying to do the alignment from gimbal bearing to engine. My old alignment bar can be...
  6. L

    Mercruiser 4.3L lift points

    Today I got a new alignment bar, But I cannot push it into my gimbal bearing even the diameter is 1.3820 inches. and The old alignment bar is 1.3740. So the old one can be pushed through the gimbal bearing.
  7. L

    Mercruiser 4.3L lift points

    The alignment bar can be pushed into couupler after I filed some high spot at the end of alignment bar. Thank you Scott06 so much
  8. L

    Mercruiser 4.3L lift points

    It seems that I need not replace the coupler. The alignment bar worked before . You can see the obvious damaged edge in the second picture. I will buy another alignment bar
  9. L

    Mercruiser 4.3L lift points

    It seems that I need not replace the coupler. The alignment tools worked before . You can see the obvious damaged edge in the second picture. I will buy another alignment bar
  10. L

    Mercruiser 4.3L lift points

    It seems that the gimbal bearing installation tools touched the coupler during the installation of gimbal bearing, the alignment tools cannot be pushed into coupler and I pushed the tools very hard and the alignment tools was broken. So I doubted coupler was damaged by me while mounting the...
  11. L

    Mercruiser 4.3L lift points

    I have found another lift point at the top. is two lift point enough?
  12. L

    Mercruiser 4.3L lift points

    Can following lift straps work or not? (This synthetic nylon sling boasts a capacity of 4,800 lb basket, 2,400 lb vertical and 1,920 choker for a variety of hoisting and lifting applications. ) https://www.princessauto.com/en/1-in-x-4-ft-lifting-sling-with-end-loops/product/PA0008480170
  13. L

    Mercruiser 4.3L lift points

    I only find one handler for mercruiser 4.3L 185HP, Where are other handlers? I am going to do the coupler maintenance and need pull the engine out.
  14. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Hi Archris, I am trying to buy genuine bellows for mercruiser alpha one and gen I. Could you please suggest which product are genuine? Could you please give me a link? Normally I prefer shopping in Amazon.ca. Thank you
  15. L

    Mercrsuiser 185HP, Unkown Serial No.

    Is the gimbal bearing good? A piece of edge of u-joint bellow house was damaged and I applied the silicon and hope it can work. Tomorrow I will install the bellows.
  16. L

    Mercrsuiser 185HP, Unkown Serial No.

    Thank you Fun times. I bought from Amazon.ca https://www.amazon.ca/dp/B09ZXMT4X3?psc=1&ref=ppx_yo2ov_dt_b_product_details
  17. L

    Mercrsuiser 185HP, Unkown Serial No.

    Gimbal bearing failed to be installed. See attached file. Can I pull it out and install again. it the new out ring is broken. Maybe I can put the old outer ring back. What reason caused the out ring failed to be pushed? or The gimbal bearing is in the bad quality?
  18. L

    Mercrsuiser 185HP, Unkown Serial No.

    Yes. I have found it.
  19. L

    Mercrsuiser 185HP, Unkown Serial No.

    I am going to install the gimbal bearing. I'd like to know how the greese is pushed into the gimbal bearing? I cannot find the any hole from the gimbal bearing house by which can be used to push grease into gimbal bearing. left gimbal bearing is old and I can see the new grease which I pushed in.
  20. L

    Mercrsuiser 185HP, Unkown Serial No.

    Can anybody help me to identify where is leaking oil from?
Top