Search results

  1. g0nef1sshn

    77' 16ft Starcraftt ss

    64osby, thanks alot, although still cheap, was able to drill 2 more fishing rod holders! Gonna cut some wood blocks and seal them and reinforce these ones. Thanks again! Also got my switch panel in today!
  2. g0nef1sshn

    77' 16ft Starcraftt ss

    After commenting on Baja's thread about how its fun sitting around and thinking about future plans, I put my girls down for a nap and went out to think about blinds. While sitting in it, two holes in the top sides were bothering me so I grabbed the box the held the old fishing rod holders that...
  3. g0nef1sshn

    Starcraft on C-list/ebay!

    heres a cool one... 1962 Chris Craft ROMER ALUM. CLASSIC,Twin 350 Inboard - $7000 (Mt.Dora/Eustis) http://orlando.craigslist.org/boa/5365492431.html 27' Alum boat Hull, Cabin Crusier,, Head, Galley, Dinning table, V Berth. Twin 350 inboards,, Eldabrock Marine Carbs, ONLY 100 hrs. Sits...
  4. g0nef1sshn

    77' 16ft Starcraftt ss

    Got a lil more work done. Attached the oh shoot handles. Not screwed into the base yet, 5200 still setting. 5200'd the exit port to the hull. Paint job will be easy to fix. hard to mess up camo! Added tie downs with SS screws. These will be for strapping in a cooler. Started...
  5. g0nef1sshn

    77' 16ft Starcraftt ss

    No tape it is. Thanks Got out in the kayak this morning for some bird watching (didn't shoot) and the sunrise. High 30's this morning made is finally feel like the right time of year.
  6. g0nef1sshn

    77' 16ft Starcraftt ss

    Ok, so I spent 5 bucks on a cheap hole drill thing and the bit tip broke on the first drill attempt. I did pre-drill a hole first too. So the bit tip breaking really shouldnt have broke like that Its just the deal with cheap stuff. Ill clean up the small angle piece and attach it to the knee...
  7. g0nef1sshn

    77' 16ft Starcraftt ss

    Not much been going on here, got some "oh shoot handles" to find a place for. had to get in the attic too sohad to pull the boat out and cleaed her out of the usual garage clutter. motor hopefully comming in the next few months. got my last aluminum sheet back in it too, need to get her back to...
  8. g0nef1sshn

    1977 Mariner 1600 rebuild

    The trailer I bought for mine only has two bunks. I think it will work fine If it had the supports already welded there I would have prefered 4 bunks like the trailer posted above
  9. g0nef1sshn

    77' 16ft Starcraftt ss

    back from a fl hunt trip..
  10. g0nef1sshn

    Starcraft on C-list/ebay!

    http://hiltonhead.craigslist.org/boa/5313769565.html not a starcraft but....... 1965 Marinetti all alum 26 footer - $12500 (NC) This is a cabin cruiser the engine is a gray Marine AMC 327 completely rebuilt transom completely rebuilt needs to finish up inside to finish an outside deck this...
  11. g0nef1sshn

    77' 16ft Starcraftt ss

    nope,going with old 20 guage remington wingmaster been shooting the last 22 years. actually just got a special UPS delivery 5 mins ago....
  12. g0nef1sshn

    77' 16ft Starcraftt ss

    Duck season starts tomorrow for me! this is my ride till I get a motor!
  13. g0nef1sshn

    77' 16ft Starcraftt ss

    Took a bit to find my data sticker but got her put on. got the seats able turned around sticker from afar and legible. thats the knife for the eventual weed build up on the prop. Nothing fancy but needed. Used to be strapped on top of kayak for a feel good gator deterent...
  14. g0nef1sshn

    77' 16ft Starcraftt ss

    thanks guys, any idea what year this rude is by chance? its on a junked glasser with controls, unknown if key is with it. Might see it today. the usually buddy left me a boat I know nothing about it but supposedly it ran before tearing the floor out the boat story. Hes asking 800, last night...
  15. g0nef1sshn

    77' 16ft Starcraftt ss

    sounds good to me! Happy Veterans today to those out there serving of have serverd! I got some duck scouting done this morning and then came home and got what I could done to the boat. I happened to have just enough carpet on hand to finish boxing in the stern end foam and cut out an area...
  16. g0nef1sshn

    77' 16ft Starcraftt ss

    Thanks Dozer. Thats stuff does get on the loose some times. I only intended to have a bead of it there just to clean up where the aluminum met. Waterman, Ill stick to waiting until Im on a computer to post the pics. I already have enough accounts and passwords to remember. Ill redo it now that...
  17. g0nef1sshn

    77' 16ft Starcraftt ss

    Thanks hayko! havnt got to your level yet. got the sides to the inside of the bench done. Wasnt supposed to be so much 5200, but the cap came off and thats how it turned out. with the lid down it doesnt matter anyway.
  18. g0nef1sshn

    77' 16ft Starcraftt ss

    Finished for the day. Still need to plan how I want the lid to open up. Still have to box in the sides. I do like the way it turned out. Not exactly square, but it will work
  19. g0nef1sshn

    need info csf 200 cc. Fiberglass Center console

    like this?
  20. g0nef1sshn

    77' 16ft Starcraftt ss

    Working lil too fast here, but used a shop fan to help dry things and get done quicker. I know dry and cured are two different things, but Im good with redoing in a few years to improve the design. Once used I will probably find a few things to redo better anyhow. Got some weight on top to help...
Top