Search results

  1. jasoutside

    Best spot for a Temp Sender?

    Hey Fellas! So the UPS guy just dropped off my new Temp Sending Unit with the "Z" bracket (contact type). I'm wondering where the best spot would be to install? I have this empty threaded bolt hole at the top of the block that would work... Should I put it there? Or, should I use one of...
  2. jasoutside

    Help trouble shooting a starter?

    1984 Evinrude 90HP So a while back I got my new to me engine running (you can see it there in my signature). Since then I swapped out the manual Tilt for power T&T, installed a new water pump, cleaned it up, painted it, and made all the connections just like they were before (well I think I...
  3. jasoutside

    Temp gauge compatability?

    Quick and easy (I think). So I bought this Temp Gauge for use on my Mercruiser V6 IO. I'm thinking I may actually want to use it for my 84 Evinrude 90 hp OB instead? I know normally Temp Gauges with the H/C are used with OB's and Temp Gauges with the actual temp readings for IO's. But, can...
  4. jasoutside

    Gears Grinding?

    OK, so I spun my shaft and here's what I'm hearing... I spun it some then at 10 sec I actually grab the shaft and lift it up while I am spinning it (quiet), let let it down while spinning it again. Are my gears grinding? Normal? Not normal? Wassup? Thanks in advance fellas! (1984...
  5. jasoutside

    Found this in my water pump housing...

    This little pin here. Found it sitting just like that when I pulled the housing off. What's it for, where is it supposed to go? I'm sure it's not supposed to be sitting in there eh? (1984 Evinrude 90HP)
  6. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration Cool thanks man!:) Yah, the instructions said that I had to use that extra stuff but it just didn't make any sense to me. Cheers:D
  7. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration Hey Dave, lil help here.... So I was just about to install my drain tubes and the Flanging Tool call for the use of the "Moeller Drain Fitting part #20848-001" http://www.jmsonline.net/moe-020848001.htm Did you use that? It really doesn't...
  8. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration Nice she got out for some fresh air:) 40 bux seems like a great deal!
  9. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration It's all good, I kinda think 2013 is a great year to put a big Starcraft in the water;)
  10. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration Looks good! Ok, what's next on the list?
  11. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration As long as you are just going easy on the scotch brite pad I'm sure the anodizing is staying in place. To get it off you really need to go big. I used a belt sander on my trim to get it off. Uh, hmmm. You mentioned the windshield, but, uh, I...
  12. jasoutside

    Compatibility of controls?

    Hey fellas, I've been looking for a good set of controls for my 1984 Evinrude 90 and came across these: http://www.ebay.com/itm/200775357594?ssPageName=STRK:MEBIDX:IT&_trksid=p3984.m1952.l2649 I realize the ad says "OMC Stringer, Cobra" but will they also work for my Evinrude? Any of you guys...
  13. jasoutside

    Expanding (pour in) Flotation Foam and Aluminum Boats

    I originally posted these videos in my Sea Nymph Rebuild thread. I thought it would be good to post them in the general section for everybody to check out and hopefully make an informed decision about flotation for their aluminum boat. Pour in foam in aluminum boats...
  14. jasoutside

    1989 15 HP Evinrude Electric Start

    Hey guys, I've come across a fella selling this 89 15hp Evinrude electric start outboard, long shaft. I'm thinking I may like it as a kicker for my 22' Islander. What are your pro opinions on this vintage? Good? Are there better years to look for? Thanks for the insight!:)
  15. jasoutside

    Manual T&T to Power T&T swap?

    1984 Evinrude 90 V4 Howdy fellas, just grabbed this outboard with manual T&T. It has that single "assist" type cylinder on the bracket. So, I'd like to swap it out for power T&T. It appears to my rookie eyes that this should be a direct unbolt and bolt up sort of change over. My question...
  16. jasoutside

    1984 Evinrude 90 HP VRO Disconnect

    Howdy gents! Just grabbed a new (to me anyway) Evinrude 90 HP VRO. The previous owner says he was running pre mix rather than the oiler. Cool with me, that's how I'd like to run it too. So I'm looking under the hood here and can see the hose is disconnected. But here's my question, is this...
  17. jasoutside

    1979 22' Starcraft SuperSport V5 Restoration

    Re: 1979 22' Starcraft SuperSport V5 Restoration Gotta feel good seeing a big chunk of stuff like that sitting in there:)
  18. jasoutside

    1975 85 HP Evinrude - bad T&T motor?

    Hey fellas, looking for an engine and came across this... http://thumb.craigslist.org/boa/2952860142.html Owner says the T&T motor is shot. Is this something the average backyard mechanic can replace? Or should I keep on looking?
  19. jasoutside

    Just stopping by to say hello - 1980 165 SS

    Hey guys, just grabbed this the other day so I though I'd swing by to say hello!
  20. jasoutside

    1980 Sea Nymph SS 165 Rebuild

    Alllllrighty! Somehow this Sea Nymph found it's way right on over to my place. I think it's awesome! (I had kind of a bad accident last night with one of my sandwich handlers, so I'm just working with the lefty now. It's going to take me a bit to get this thread caught up to current.)...
Top