Search results

  1. JonBoat55

    Shift shaft seal / carrier seal / oil o-ring?

    What would be the direct issue of gear oil seeping down the upper shift shaft onto the lower shift shaft assembly?
  2. JonBoat55

    Shift shaft seal / carrier seal / oil o-ring?

    Correct. I figured worst case, I'm wasting a bit of money for the sake of preventative maintenance. Nope, that wasn't the worst case haha
  3. JonBoat55

    Shift shaft seal / carrier seal / oil o-ring?

    I'm kicking myself, my boat is a 99. I've had it for six years with no issues, this season I decided to do some extra maintenance and do the shift shift assembly and carrier assembly, Have never had oil leaks before and now I do.
  4. JonBoat55

    Shift shaft seal / carrier seal / oil o-ring?

    Split the drive and found the shift shaft assembly soaked in oil. Pressure tested and found the leak in the oil bushing gasket. Just installed the part two days ago. Serves me right installing Sierra parts. I can see that oil coming out of those weep holes could be either the shaft assembly...
  5. JonBoat55

    Shift shaft seal / carrier seal / oil o-ring?

    New gear oil leaking out of the lower unit holes after putting the out drive back together. Which seal is to blame? Water was flowing out of holes when running on the hose. Drained oil after seeing the leak, no water in oil.
  6. JonBoat55

    Out drive water flow incorrect?

    The speedo tube is in front of the shift lever, I had the connection secured to it during the video. The water looks like it's coming from way above the plate where the speedo tube connection is
  7. JonBoat55

    Out drive water flow incorrect?

    1999 Regal 1800, Mer 3.0, Apha1Gen2 Just finished doing end of season maintenance. New impeller kit and all gaskets, shift assembly and gaskets for the lower. Pulled the upper to inspect everything (u joints, alignment all looked good) and replaced with new gaskets and o rings. Put everything...
  8. JonBoat55

    Alpha 1 Gen 2 shift shaft seal replacement

    Should this lower (1999 A1G2) also have a shift shaft sleeve installed? (Mercruiser 23-67370) I've never had this part on my lower, but im wondering if it should.
  9. JonBoat55

    Alpha 1 Gen 2 shift shaft seal replacement

    Thank you for the info, ordered.
  10. JonBoat55

    Alpha 1 Gen 2 shift shaft seal replacement

    Looking for info on a part. Found some water in lower oil while changing it, pressure test found the issue was the shift shaft bushing, seal was torn and all oily. The replacement I got is missing this washer. I can't find any info or part number for it. Only thing I can find is a shift...
  11. JonBoat55

    Reminder to check gear before towing.

    Found a beat up cooler upside down on the side of the road right off the highway in update NY where we camp. Just got into town and saw it, pulled over, full of PBR, ice was still cold. Ive been trying to duplicate that kind of luck every since
  12. JonBoat55

    Scary

    Where are you located? I've noticed some of the same here in CT
  13. JonBoat55

    Mercruiser Exhaust Tube vs Exhaust Bellows Opinions, and Part # for Tube.

    I had the tube on my Merc 3.0 for three seasons until I did all the bellows at once, so I re-installed the exhaust. I like it being slightly quieter, not a huge difference. Interestingly enough, I think I can feel a slight rumble/vibration through the steering wheel now since the exhaust is...
  14. JonBoat55

    3.0 mercruiser dieseling

    My 1999 carbed Merc 3.0 came to me with a 160 thermostat installed. Had slight dieseling issues and warm start issues for a couple seasons. Eventually swapped it out for a 140 and havnt had any issues since.
  15. JonBoat55

    1988 mercruiser 5.0 alpha one

    "Bad gas mixed with good gas just equals more bad gas" Its amazing how much carb engines hate bad gas. I didnt believe it till I experienced it on my own years ago. Had lots of engine problems, fixed them all when I stopped messing around and pumped all of last seasons fuel out. Added fresh...
  16. JonBoat55

    What kind of damage from an I/O in salt water for 2-3 years?

    Do you have pictures? Make/model of the boat? Make/model of the engine? Been floating at a marina, private dock, mooring? You are asking a lot of specific questions with very little detail guys in here would need to make those answer worthwhile.
  17. JonBoat55

    3.0 mercruiser dieseling

    What kind of engine do you have? Raw water cooled? What temp is it running at?
  18. JonBoat55

    Going straight at low speed?

    Assuming you’ve got an I/O, you can check the gimbal ring. Mine had gotten a tad loose and once tightened to spec (carefully) it improved the wander at slow speeds greatly for me.
  19. JonBoat55

    Florida snow

    Just came back camping in upstate NY Adirondaks, more snow in Florida
  20. JonBoat55

    Gun ownership and permits.

    Oh boy, I thought we werent trying to get this thread locked down...
Top