Search results

  1. Scott Danforth

    Livorsi Wire harness diagram

    You will have to call Livorsi
  2. Scott Danforth

    Expanding foam (for transom reinforcement) Anyone done this?

    Foam is for flotation until you get to the 8# and 16# density foam
  3. Scott Danforth

    [SPLASHED] I/O (Sterndrive) Conversion to Outboards

    Carnac says 33 gallons isnt fuel dock prices $6/gallon in Boston?
  4. Scott Danforth

    [SPLASHED] I/O (Sterndrive) Conversion to Outboards

    there is no fuel economy on a boat unless you have sails or oars......
  5. Scott Danforth

    Artificial Intelligence

    August 29th is right around the corner
  6. Scott Danforth

    1997 5.7L thunderbolt ignition. Slow crank

    Yes, that is a carter electric pump
  7. Scott Danforth

    Fishing with Dad

    With the rainy season here. going to make new canvas bows for the boat. been meaning to for about 3 years now. getting tired of water pooling in the canvas. really need to sand the boat down and repaint it.
  8. Scott Danforth

    Lost my mooring

    thats great. last I remember, you were splitting the sail boat cap from the hull. did that ever get finished?
  9. Scott Danforth

    Better solution for this "seat"

    thats just a pedestal. you need to mount a seat to it
  10. Scott Danforth

    1986 Baretta 3.0 mercruiser

    it should hold 15 psi with the valve shut off for perpetuity. if it leaks air, you have a leak.
  11. Scott Danforth

    No Reverse or Neutral....just Forward VP

    First, follow the manual on adjusting the linkage at the outdrive. that involves removing the cover on the back of the drive. (item 72) the football shaped linkage is what shifts the transmission make sure the whole assembly back there is adjusted per the manual. (the crusty pic below is...
  12. Scott Danforth

    1992 OMC 3.0 Cracked Block

    first, welcome aboard that block went thru a freeze. the block is busted on the outside where you see it, and on the inside, just above the pan rail the rusty goo in the upper right of the corner says your manifold was also freeze busted. you need a new motor. since it sat with water in the...
  13. Scott Danforth

    1997 5.7L thunderbolt ignition. Slow crank

    Ask which head gaskets and if it has brass core plugs. Also ask which cam as that look like someone went thru it.
  14. Scott Danforth

    volvo 434a carb base gasket

    You need an isolator gasket for a spread bore carb if your motor has a 4175
  15. Scott Danforth

    Best Flushing Ear Muffs? Mine aren't working

    Measure your hose pressure and flow
  16. Scott Danforth

    Lakesport TX17 rear deck removal

    Look in the carpet pile for screws
  17. Scott Danforth

    Engine misfires after rain storm

    you should have the crab cap..... those are a replace nearly every other year regardless type of thing. because the cap breaks down internally.
  18. Scott Danforth

    stripped SX-A (3L VP) dipstick threads

    or pull the cap and take it to your local radiator shop. they will weld it and re-tap it for about $30
  19. Scott Danforth

    1997 5.7L thunderbolt ignition. Slow crank

    here is my typical starter and electric fuel pump wiring. verify the oil pressure switch connections, they are not standardized between brands. The relay connections are standardized. with "0" oil pressure, cranking the motor provides priming and ignition with over 3psi of oil pressure...
  20. Scott Danforth

    1997 5.7L thunderbolt ignition. Slow crank

    truck cams are really really really close to marine cams
View older results
Top