Search results

  1. Superjetjim

    Mercruiser 4.3 Vortec running hot on one side

    Here’s a picture of my water routing. Are there balls inside this housing? One side has steam / water mix from exhaust - other is just water.
  2. Superjetjim

    Mercruiser 4.3 Vortec running hot on one side

    Got a strange problem with differing water flow and temp between left and right hand side of engine. Motor has been stored for a long time, drained antifreeze. Lots of crap brown water came out of blue block drains. Now running clear and reinstalled them. After a min or so of running the right...
  3. Superjetjim

    Mercruiser 4.3 carb weep

    All sorted thanks, mechanic tightened it up more than I felt comfortable doing
  4. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Yes!!!! Result!! She’s a runner. Thanks SO MUCH to you guys on here for your help and persistence. All it needed was the timing mode and light and away she went. The Mercruiser mechanic had it up and running in 30 mins. Short clip attached. I’ll connect it up to the hose and run it for half an...
  5. Superjetjim

    Mercruiser 4.3 carb weep

    Hi I have a slight leak between the two nuts on the fuel pipe as they enter the carb. Can you use a small amount of plumbers tape between these nuts to stop it or should I look elsewhere / tighten further?
  6. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    I have it booked in at a Mercruiser dealers tomorrow, lets see if they can adjust the timing and get it running. Will report back.
  7. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    How do you tell which type I have?
  8. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Thanks for the reply. I had the carb off rebuilt it (I’m familiar with rebuilding carbs have done several before) I poured fuel using a squirty bottle down the carb a couple of times. It fired momentarily as in the video. But nothing more. I also tried manipulating the distributor cap about...
  9. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    No I don’t have one, plan was to test it at 0 degrees and if it ran go from there.
  10. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    So I have bright blue spark in all plugs. Compression readings from a moment ago: 1) 155 3) 157 5) 135 2) 125 4) 175 6) 90 Even with no6 on 90 it would run and ‘carry’ that piston right? If I wanted to check the timing with a timing light is that all you need, the light? Do you need to put...
  11. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Got a second attempt to start the motor today - no backfires, but sadly I think the motor is toast. I’ll check the compression again tonight, suspect the oil that was in the pots and providing good compression has now gone and its low again. I went through a couple of good batteries cranking it...
  12. Superjetjim

    Power Steering Pump thread?

    Does anyone know the thread / diameter of the flared hose that screws into the Power Steering pump on a Mercruiser please? I need to buy a barbed fitted so I can loop it back to the return on the pump for testing purposes out of the boat. It’s a 1998 Vortec 4.3.
  13. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Quick check (and this might be a red herring) - but on this video the guy has his No1 dissy post at the back (where mine was) rather than at the front as per the above diagram - does that matter?
  14. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Thanks this really helped. Timing set and leads removed, traced and labelled to help in future - will try and start it tomorrow. If its a runner and sounds OK I assume we're into timing lights to do the dynamic timing? - or does that need to be done before I try and start it?
  15. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Right chaps, firstly thanks for all the help / pics. So removed rocker cover / plugs and turned over until on compression stroke / valves closed and aligned notch on case as seen. Dissy marked case marked and rotor marked for cylinder 1 and spun about 180 degrees and reinserted. Screwdriver...
  16. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Yes that’s what I meant - front of motor, sorry! 👍🏻 Understood 👍🏻
  17. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Thanks, so when the TDC lines on the flywheel and cases aligned and both valves on No1 are down that’s the TDC I want right? Then set the disi as per the video?
  18. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Thanks for the help guys, I’ve just been looking at the motor, this is where the number one HT lead connects to the current distributor, it appears to be exiting the back not the front of the distributor pointing towards number one cylinder where you would expect it to right?
  19. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Found an American car service specialist a few miles away. Might take it there tomorrow and get them to do it, I’m out my depth here and don’t have a timing light either. 👍🏻
  20. Superjetjim

    Mercruiser 4.3 Vortec Backfire and no start

    Thanks guys, I’m a two-stroke guy and find this highly confusing, sorry. Is this video exactly correct and what you’re talking about?
Top