Search results

  1. kramerpage

    Need instructions how to remove merc 2000 3.0 L Engine from Boat

    I got it ready to pull Chris except the rear and front engine mounts. I have trailer it 5 miles to a metal fab shop so I want to wait until its there to get those. I then have to re install the motor. Install all new rubber in the outdrive gimble/transome plate and service the outdrive water...
  2. kramerpage

    Need instructions how to remove merc 2000 3.0 L Engine from Boat

  3. kramerpage

    Need instructions how to remove merc 2000 3.0 L Engine from Boat

    Hello all, Good to be back on the site and see some of the same folks from years back. I need to pull the engine to repair the transom in an aluminum boat. I tried the boatfix links and it just stays dark and search but many of the links are old. Thanks for any assistance.
  4. kramerpage

    1994 mercury 135 V6 warning horn alert

    while trolling last weekend my warning alert started an intermittent beep, beep sound at the helm. This motor has the oil injection blocked off kit using a 50 to 1 mix in the main fuel tank. The lubalert as mercury calls it or oil alert module is still wired to green going to coil #2, tan/blue...
  5. kramerpage

    1993 WMH 28 carb 135 hp

    Can anyone tell me what this part is? Some carbs have them and some not. Do I need them? Cannot find them on Mercury parts site. Thanks
  6. kramerpage

    1993 135 Black Max Twins stalling

    I took the carbs off my spare power head. I see they are numbered 123 3 on bottom 1 on top. my question is what's the difference between them? I'm guessing I rebuild them one at a time due to the differences.
  7. kramerpage

    1993 135 Black Max Twins stalling

    Last year they ran great. This year I have an increasing problem with the engines stalling. Scenario 1... port is forward and starboard is in reverse to enter slip at idle Scenario 2 both at idle and may run for 10 minutes fine and all the sudden on drops out and wont restart unless you...
  8. kramerpage

    1993 135 Black Max Twins Trolling question

    Hello, I use these motors to troll on Lake Erie at around 800 to 1000 rpms to troll while fishing. I only run one motor while trolling. I try to rotate motors to distribute run hours. I troll on weekends say 4 - 5 hours a day. My question is there any special spring maintenance that needs to be...
  9. kramerpage

    Merc 135 1994 Spark Plug

    Can someone tell me what plug to use? #0G001404 Thank you
  10. kramerpage

    1994 Mercury blown power head ( twins)

    GOOD NEWS: I found a 1992 replacement motor in Baton Rouge LA on craigslist Thursday night. Made a trip to perch fish Friday am got our 90 fish and headed to LA. Drove non stop 16 hrs and arrived in Gator Country. Ran motor, everything looked good. Few very nice young men helped me load and off...
  11. kramerpage

    1994 Mercury blown power head ( twins)

    Last weekend my port engine blew a hole in the side of the block. I have been searching for a powerhead and cannot find one. Its a 1993 manf date CXL 135 2.5L serial # 0G001404. I called Crowley, Mercury reman., and OBParts all stating there are none in stock. To repower with controls is 24K...
  12. kramerpage

    1994 Twin 135 HP Mercs Can they be silenced??

    The kids probably want them louder. Im used to I/O. These motors are loud. Can you insulate them? Why and or what is so loud in them? They run great. Lots of power but man the noise...Thanks
  13. kramerpage

    1994 TWIN 135 hp black max V6's switchbox failure

    My last trip out my port motor experienced a reduction of 1000 rpm at WOT. The marina checked compression and said it was great. They state they found a faulty switchbox. Replacement is 238.00 for part and 2hrs labor including troubleshooting. MY question is can a faulty switchbox reduce wot...
  14. kramerpage

    1994 TWIN 135 hp black max V6's Oil Pump block off parts

    So one of my motors has a block off plate and the other has the oil pump with hoses cut off and bolts stuck in them with clamps and wire ties. It looks like a disaster. I am trying to figure out what parts I need, to remove oil injection parts as someone else did to the other motor. My shop...
  15. kramerpage

    My Rotten Lady

    Well I guess this is one way to do it... I'm taking my girl out to get a new dress and winter coat...
  16. kramerpage

    1994 135 hp black max V6 Battery Charging System Troubleshooting 40 AMP

    Here is a pic of the two regulators. As you can see the yellow conductors were open from high resistance at the connector which led to overheating and eventually failure.
  17. kramerpage

    1994 135 hp black max V6 Battery Charging System Troubleshooting 40 AMP

    I do not have rising battery voltage when the motor is at 1000 rpm and above. I believe my first step is to check wire integrity from battery + to starter solenoid. From there to the pair of red wires to each voltage regulator. The pair of yellow wires going to the stator. Just to look for...
  18. kramerpage

    How to adjust the idle on 1994 135 hp black max V6

    Here is what I found in manual.
  19. kramerpage

    How to adjust the idle on 1994 135 hp black max V6

    How do I adjust the idle on 1994 135 hp black max V6. My tach says 1000 in neutral. I need to get it down to 700 - 800. 1000 seems hard on the lower unit to me. Thank you
  20. kramerpage

    My Rotten Lady

    I received two new bucket seats today that I ordered in May. I'm happy with them. Half the price the upholstery shop wanted to redo my original. Also I got the trailer under the boat and placed roller skates under it so I can easily adjust bunk boards and move entire boat around. Me like them a...
Top