Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
pro mariner 20 plus onboard charger wired under the bow with a 110 port panel mounted just below the FF Casting seat with height adjustable pedestal
Baystar Hyraulic steering and a sweet new wheel provide...
Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
remote control spotlight tidied up the hydraulic streering lines and motor wiring crowded dash ;) but it works minnkota alternator charge aportioning unit to share 60 A output from the motor between 3...
Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
interior pics added a passenger side rod locker door to match the driver side. Baitwell added under splashwell
electronics upgrade includes merc monitor and gateway passing data to HDS-10, HDS-10 linked to new...
Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
almost done now, just have to get new canvas made.
holes in the transom below the waterline from the po mounting a transducer patched with epoxy putty (cold weld) then sanded primed wiith chromate spot puttied...
Re: How to install a SMARTCRAFT system
stored pitot tubing on the lower front port side by the engine harness pass through grommet
pressure senders connected to water pressure tubing and pitot tubing
Re: How to install a SMARTCRAFT system
grommet installed wires routed and tested to clear throughout trim/tilt range
water pressure fitting water pressure tubing installed in the sender
Re: How to install a SMARTCRAFT system
trim wires entering the bottom of the cowling, grommet fremoved to thread the wires trim cable secured on bracket as the original wiring routed, ready to re-install the grommet
Re: How to install a SMARTCRAFT system
Harness and 2 pressure senders installed
Stock analog trim sender
trim sender tab fits in this screw slot which rotates as the engine moves up and down Digital sender with tab
Re: How to install a SMARTCRAFT system
lower rear starboard side, capped connector for the digital sender harness. The weather cap is secured to the plate with a small grey connector. that one can be cut off to remove the cap and a new one is included in the kit.
open holes in the plate for...
Re: How to install a SMARTCRAFT system
Received my smartcraft conversion kit for 75-115 FourStrokes today, couldn't wait to get it installed and tested. All went well, great instructions but here are my pics and notes to supplement. here are the contents of the kit, digital harness, digital...
Re: How to install a SMARTCRAFT system
just a few pics of the fuel oil paddle connector on a current FourStroke as well as the Digital trim connector
This is the connector and using the weather cap ( just the other half of the connector with rubber plugs where the wires go) I inserted a pink...
Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
the baitwell is plumbed in, the fuel tank and baitwell got a light spray of expanding foam just to keep them from vibrating, original deck went back dow with 3/16 x 5/8 alum pop rivets and a fresh coat of...
Re: Building a Live Baitwell
I'm using a bucket cooler I found at the recyclers for $5, just added through hull fitting on the bottom plumbed into the livewell drain and an adjustable flow areator plumbed into the livewell supply wih a second through hull fitting near the top as an overflow...
Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
Working on the breaker panel wiring today. Fab'ed the case from sheet alum scraps and a few strips of diamond plate, populated with surplus Milspec Aircraft DC breakers
Re: 1996 Legend V17 Guide (aka Smokercraft stiletto 16) built in tank Mod and resto
A few more pics, consoles with Hydraulic steering and new wheel installed :D pass through installed in the upper transom, press fitted alum tubing passing 1/4 inch past the double alum inner wall and outer...
