Recent content by jiffyboat

  1. J

    etec oil pump in the ficht brp motor

    I was wondering is anybody have tried to install a etec oil pump in a ficht BRP motor ,since the 2004 200HP is obsolete, and impossible to find new , or no rebuild kit is available either .. this pump basically will take this motors out of the market totally
  2. J

    2004 Evinrude DFI , powerhear bolts torque specifications

    hi guys , I need the a chart with bolt torque specifications for a 2004 Evinrude 200HP DFI ..
  3. J

    2001 Mercury Optimax 150 Fuel in the intake

    hi guys, I have this 2001 Optimax 150 , with good 90psi f compression, , well the problem is that ii starts , them the rmps go like wot wish eventually I have to turn off, and I found , a lot of fuel in to the intake , I guess this is what is causing the high rpms , but I can figure out from...
  4. J

    1996 Jonhson 200HP spark on two cylinders only

    this motor have only two cylinder with spark.. the two on the center of each bank .. battery is full charged, and the motor turn fast.. I did disconnect the two rectifier wires , and still nothing .. compression is good ,I just got this boat and was seating for more than 5 years.. initially it...
  5. J

    2004 225HP DFI two upper cylinder no firing

    hi, guys, I have a 2004 225HP DFi and the two upper cylinder where no firing, on the water we noticed the misfire and started checking pulling the plug wires and noticed the two upper had no spark.. at idle or highter speed , took it to the dealer and mechanic said the the he had a good spark...
  6. J

    1995 force 70HP out of timing

    motor have 120psi compression, single carburetor , new spark plugs, starts but missing and spiting like held ,, checked the timing and is like 90 degree off, checked the flywheel thinking mayve the key broke and the flywheel of off , but is fine, have the feeling is the switch box just shorted...
  7. J

    some body have a pic of a boat weight and capasity for 1996 Proline Stalker

    need a pic of a weight and capasity stiker for my 1996 Proline Stalker 17' , this is no iligal to be copy so don't be afraid to helm me ..thanks
  8. J

    Yamaha 2006 50HP bearing problem

    have a 2006 50HP Yamaha two stroke.. and the upper bearing is no holding tight in the upper side of the crankshaft.. in other words is spinning around the crankshaft and waring the crankshaft.. wanted to weld it but the welder told me that I can get like a steel bushing to fill the gab between...
  9. J

    Corrosion in the Lower unit studs..

    trying to remove the lower unit out of my 2002 mercury 90hp four stroke ,to change the water pump, found white corrosion in three of the studs and the lower unit won' t come out........... any tricks out there?.. I have been spraying PB Blaster.. but I don't think it will penetrate that far...
  10. J

    1998 Johnson 115 HP J115TSXECM ... where are the Thermostats?

    want to change the stats to this motor J115TSXECM 115Hp 1998 and can't find them.. boat.net diagrams won't show them aether.. I'm about to think that there are not any..
  11. J

    internal noise

    Evinrude 150HP 1995 60degree motor, in idle or under load at low speed like 10 15 mph it sound perfect, at higher speed 20-30 mph , I can heard like a knocking noise , wish is not consistent, it sound different every time.. .. any idea what is the most common problem, I know I will need to...
  12. J

    Is this normal?

    OK I have a a 1997 Mercury 75HP two stroke the 75ELPTO , the motor have 120psi compression, it fires right up, and I can say that it runs fine at idle, ....carburetors and fuel pump just rebuild, new plugs, clean fresh fuel , but the motor sounds under accelerations like if a cylinder is no...
  13. J

    My good firingJohnny 150 got hurt after another oil pump fail

    Re: My good firingJohnny 150 got hurt after anthere oil pump fail Re: My good firingJohnny 150 got hurt after anthere oil pump fail ok gays this is what I found , pulled the carbs, and found that there was water inside the carbs, the bottom one had like half , water-fuel, the middle one like...
  14. J

    My good firingJohnny 150 got hurt after another oil pump fail

    had many boats and several Johnson Evinrude motors and always disconnected the oil pump system, personally as automechanic and many year working in outboards , think that the Johnson Evinrude oils pump system is a big POS, but in this case the motor was very well smoking like the Jonnys and Evin...
  15. J

    1995 Force 120HP..water into the cylinders

    hi, ..got this motor , checked the compression , came out fine, 130psi per cylinder, put it in my Bayliner , and it was running rough , did the carbs and FP and still the same , it was hard to crank the motor and the starter getting hot, pull the plugs and find water in the plugs, pull the...
See more
Top