Recent content by HighTrim

  1. HighTrim

    1956 Johnson Javelin starter

    This Should Help!
  2. HighTrim

    1956 Johnson Javelin starter

    Here is how you wire it up. Don't fret, there is nothing major wrong here, just some wiring to fix up.
  3. HighTrim

    1964 Johnson 3hp Model JH19A Serial # 101739 Rebuild

    Then, after your ignition is all set, your carb is cleaned installed, and static setting of low speed needle, you need to linc n sync. See the attached picture. When your speed control lever is within the dotted line, or 2 embossed dots, your throttle plate should just start to open. To...
  4. HighTrim

    Johnson Seahorse 5.5hp CD-12 restore

    Very typical. Your shock absorber is sprung or broken. Sometimes you can put them in vice and press back together. If they are broken, you cannot. You CAN weld them if you get it real straight, but then you wont have any protection for your powerhead of course. They are still available...
  5. HighTrim

    59 Super Seahorse 35hp lower seal kit spare stuff??

    You can see it here in the parts breakdown http://www.marineengine.com/parts/johnson-evinrude-parts.php?year=1959&hp=35&model=RD-21&manufacturer=Johnson&section=Gearcase+Group I also attached a pic of how the gasket sits with the bushing.
  6. HighTrim

    Aftermarket ignition coil for sportsman?

    another example
  7. HighTrim

    2-line pressure tank question

    Here is a diagram so you can visualize what we are talking about.
  8. HighTrim

    57 Golden Javelin Powerhead Replacement?

    It may be worn rings, but not necessarily. Its good you have verified your gauge, that would be step 1. Ensure that the compression release is not activating, or the valves are not stuck open, which would limit your compression readings. Its also good that the compression readings are very...
  9. HighTrim

    Suzuki 15hp Gearcase Drop

    Afternoon Gents, Im going to go and do a water pump on a Suzuki 15hp model 929185 (1992??) I have not done one of these before. Where is the shift rod disconnect on them? Want to have the tools I will need when I leave. Thanks
  10. HighTrim

    Restoring Some 50s OMCS This Fall

    A few that have been finished up this winter so far, ready for the water next year!
  11. HighTrim

    1998 Seadoo Speedster 787 Motor Repair

    I have a brand new rebuilt motor in my 1998 Speedster. Starting at the dock, the plastic rave valve bushing threads stripped, so rave valve dropped down onto piston, scoring it and breaking piston ring. To repair, do I need to pull carbs to get the bottom exhaust manifold bolt out? I would...
  12. HighTrim

    1958 Johnson 35 hp RDS-20 wiring problems

    Re: 1958 Johnson 35 hp RDS-20 wiring problems You need a switch with two M poles for the kill circuit.
  13. HighTrim

    1958 Lark 35hp knocking

    Re: 1958 Lark 35hp knocking yeah 220 to 240 inch/lbs Start with half torque, then 3/4, then the full 220 Spiral pattern out from middle as shown. You could trace/cut gaskets>?
  14. HighTrim

    I just got 1958 Evinrude big twin 35 and I know nothing about it

    Re: I just got 1958 Evinrude big twin 35 and I know nothing about it Great motor! The '58 year in Johnson and Evinrudes are great lookers. Here is a copy of your wiring diagram. To make it short shaft, you will need to drop the gearcase. The drive shaft will need to be swapped. The water...
  15. HighTrim

    Evinrude 18 hp 1957 not starting

    Re: Evinrude 18 hp 1957 not starting This would be the '59 Fastwin.
See more
Top