Search results

  1. C

    How to replace temp switch

    I have 1997 40hp with s/n 0G565379. I want to replace temp switch 87-16775A3 was mounted on block. How do I remove it. Thank you for any ideas
  2. C

    Alarm beeping

    Looking for some advice, I have mercury 1997 40 hp 4 cylinder oil injection, with S/N 0G565379 , when starting motor alarm keeps on beeping even after disconnect tan wire from sensor and replaced low oil alarm module. Any info will be appreciated, Cal
  3. C

    Merc 1997 40hp 4cylinder solenoid check

    Hi, everyone out there, I have Mercury 1997 40 hp 4 cylinder oil injection, what am I supposed to read when I check out solenoid with ohm meter red probe to yellow wire black probe to black wire, when I do that it red opened 12ohms low resistance, I also check it with volt meter when turn key...
  4. C

    Mercury 40 hp mixture adjustment screw

    Hi, I have 1997 40hp 4 cylinder 2 stroke, s/n 0G565379, nood to locate mixture adjustment screw, Thank you 4 info
  5. C

    1997 mercury 40 hp 4 cylinder 2 stroke

    I have Mer 40hp 4 cylinder run hot at startup, water peeps okay,seems to be high idle also.please help
  6. C

    full advance spark timing setting for 1990, 50 hp?

    hello, all experts I have 1990, 50 hp, 2cycle Evinrude, model #VE50BELESR, S/N G02535055. I replaced power pack with conversion kit(113-4489) the instructions say to reset ignition timing to the service manual. does anyone know the full advance spark setting for this motor? any info will be...
  7. C

    Evirude 1990 50 hp, fuel pump?

    Hi, everyone. I have 1990 Evinrude 50 hp having a hard time starting until spraying some fuel into the carb. How do I verify if my fuel pump working normally? what is this called? the orange tab should be down or up? thank you.
  8. C

    RPM at w o t only go up to 3000 rpm?

    Hi, experts out there. I have Evinrude 1990, model# VE50BELESR, SERIAL # G02535055. After replacing power pack with new conversion kit {113-4489), I do the run test at first couple times at w o t, it seems to be normal seeing RPM at about 5500 for a while, after that when warm up, It seems to...
  9. C

    where to refill trim cylander on 1990 50 hp?

    I have 1900 Evinrude 50 hp 2cylanders, 2 stroke, Where do I refill the fluid? and what kind of fluid does it need? It is stuck , used to get it up and down by hand. now it is a lot harder to lift it up by hand. Model #VE50BELESR , S/N G02535055. Thank you for any suggestions.
  10. C

    Throttle plate won't return all the way back?

    Hi all experts out there, I have 1990 Evinrude 50hp, 2cylander, 2 stroke. I replaced ignition pack under flywheel after tightened 6 screws for top plate and bottom plate together, then I check the control handle by advancing it all the way and return it to the neutral position my throttle...
  11. C

    1990 evinrude with s/n G02535055 pwr pack dva output?

    what would be the voltages from pin #1 and #2 from pwr pack when engine runs? thank you.
  12. C

    Techrom metor

    Hi, any one, I have 1999, 30 hp, Mercury with oil in jection. There is 1 connector from side control. Is that for techro metor? Thank you
  13. C

    Won't above 1500 RPM when in gear or out off gear?

    I have Evinrude 1990, model# VE 50BELESR, when gives it more fuel it dies. checked compression 119, 221 psi, pulled out carbs and cleaned them also checked spark jump at 7/16 of an inch seem to be okay but whem pull out either spark plug boot it dies, run out of ideas. where do i need to start...
  14. C

    choke level works?

    Hi, any expert out there. I have Mercury 1999 30hp. 30E0, serial#06762519, oil injector. having a hard time starting cold, when i started it at home with muffs it take a few cranks only, when i took it to the lake it takes about 10 times to get started. is there any adjustments does it...
  15. C

    How to remove steering tube from 1999 30hp.

    I just bought Mercury 1999 30hp oil injection, with rusted steering tube can not slide a steering cable through. thank you.
  16. C

    1999 Mercury 30 hp, how to remove steering tube?

    I just bought 1999 oli injector 30 hp with rusted steering tube, can not slide the steering cable through. have been trying to clean rust out with drill but still can not slide the cable through. how do I remove it?.Thank you for any help.
  17. C

    Evinrude 50 hp V R O pump?

    I have Evinrude 50 hp With serial # G02535055, Model # VE 50bELESR. won't above 1500 RPM, It is cutting off try to die. Have done Commpression checked 122 Top cylander, 119 bottom cylander, spark checked at 7/16" and pulled carbs cleaned and blew each passage with compressed air, it is still...
  18. C

    Evinrude 50h serial # G 02535055. Model #VE50BELESR

    hi, any expert out there. I have Evinrude 50 hp out board only know the serial # and model# up there. Can't go full throttle or above 1500 RPM, the motor tend to die, was running perfect last summer, a motor starts up and pump water very good. any ideas or advice will be appreciated, Cal s...
  19. C

    Evinrude 50 hp outboard lower unnit dropping

    I have Evinrude 50 hp that I try to lower unit to check the gear case because I ran over log. now motor vibrate when in gear, please tell me how to drop it. I unbolt it, it only dropped 1/4 inch lower. Thank you in advance,
  20. C

    evinrude 50h unable to go full throttle

    Evinrude 50h serial # G 02535055. Model #VE50BELESR. Ran over floating log, unable to go full throttle with excessive vibration and noise shortly after. Any advise where/what to check? Anyone can help me on how to lower the lower unit to check the gear case. right now, I dropped lower unit, but...
Top