Shop
Community
Home
Forums
New posts
Search forums
What's new
New posts
New media
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
New media
New resources
Latest activity
Menu
Log in
Register
Install the app
Install
Home
What's new
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Latest activity
What's new
New posts
Latest activity
T
tphoyt
reacted to
saltchuckmatt's post
in the thread
1993 Johnson 9.9 lower cylinder wet.
with
Like
.
Did you replace the impeller? A motor that's sits that long is bound to have cracked rubber. Swap coils, ohm everything out and if it...
Aug 25, 2026
Scott Danforth
replied to the thread
2-4-C
.
I have been using a lot of farm implement greases lately. I use a lot of John Deere cornhead grease at work for worm gear actuators...
Aug 25, 2026
Scott Danforth
reacted to
alldodge's post
in the thread
2-4-C
with
Like
.
When I get a newer 8.2 with Gen 3 cool fuel I will be changing it over to older Gen 2 or even a Aeromotive (or other) with return to...
Aug 25, 2026
Scott Danforth
replied to the thread
Power Steering Pump - Angled Mount
.
If your pulley is off and the belt isn't aligned, adjust the pulley installation until it's aligned The pulley installation or removal...
Aug 25, 2026
Scott Danforth
replied to the thread
Stainless Steel Rowboat
.
They made Stainless StarCrafts.
Aug 25, 2026
bowler
replied to the thread
What is the Best Way to Repair the Snaps on a Sunbrella Cover
.
Find an old singer 201k sewing machine. They cost pennies and are more than capable of sewing boat canvas.
Aug 25, 2026
Berdink
reacted to
racerone's post
in the thread
Any clue what this gunk is?
with
Like
.
The issue is perhaps the thermostat missing or stuck open.---Help yourself and post model # here !----I can not see / look over your motor.
Aug 24, 2026
S
saltchuckmatt
replied to the thread
1993 Johnson 9.9 lower cylinder wet.
.
Did you replace the impeller? A motor that's sits that long is bound to have cracked rubber. Swap coils, ohm everything out and if it...
Aug 24, 2026
S
saltchuckmatt
replied to the thread
1989 3cyl 75 HP Evinrude - Running on One Cylinder? (Videos Included)
.
The ones you put on still need to be shrunk on both ends ...you missed a step. I have no problem with the bullet connectors. After...
Aug 24, 2026
S
saltchuckmatt
replied to the thread
Any clue what this gunk is?
.
Confirms what the original milky flavor was.
Aug 24, 2026
nola mike
replied to the thread
Question regarding wiring up a carter electric fuel pump
.
Yes/depends on the ignition
Aug 24, 2026
M
Mc Tool
replied to the thread
1993 Johnson 9.9 lower cylinder wet.
.
Swap the plugs over and see if the fault follows .....might just be a duff plug 🤞
Aug 24, 2026
R
Robobrainiac
replied to the thread
OMC 4.3 Electronic Ignition Swap
.
I was able to borrow an equus dwell meter from my dad. I installed new Sierra points and condenser, new standard motor products ignition...
Aug 24, 2026
J
Johnnyl30y
posted the thread
200 venom idle and runability
in
Johnson & Evinrude Outboards
.
I recently traded for a boat with a blown 1995 johnson 200hp venom motor. I did a powerhead swap and have struggled to get it running...
Aug 24, 2026
A
Abefish0
posted the thread
1993 Johnson 9.9 lower cylinder wet.
in
Johnson & Evinrude Outboards
.
Hello, I recently bought a 1993 Johnson 9.9 2 stroke outboard. It was sitting for close to 20 years but the previous owner ran it out of...
Aug 24, 2026
Home
What's new
Top