Water up drive shaft

pfj57

Cadet
Thread starter
Joined
Jun 25, 2018
Messages
6
2000 Johnson 90 60’ V4, 20’ shaft. Replaced water pump and gear oil. Started up and getting what looks like water traveling up drive shaft. Does not enter cowling but discharges down outside of mid section. Also not getting water out of bottom vents on lower unit. Any suggestions would be greatly appreciated.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Can't say about your particular model, but the usual cause of that is the seal on top of the water pump housing was left out.
 

McBinary

Cadet
Joined
May 29, 2018
Messages
10
I don't know specifically about that model - but usually the water pump has a pipe that extends from the top of the pump that needs to be seated correctly further up the drive shaft to be expelled out the water "exhaust". If it's not in that plug, it would expel within the housing.
 

pfj57

Cadet
Thread starter
Joined
Jun 25, 2018
Messages
6
Thanks I have included the o-ring at top of housing and have made sure fit to water is right. I have looked at the housing several times and can’t come with something out of place. Should have included that the pee hole is streaming correctly.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Don't know if this is your motor or not, but I was speaking of part # 61. It is what keeps water from entering the drive shaft tube.
 

Attachments

  • photo294092.jpg
    photo294092.jpg
    8 KB · Views: 0

pfj57

Cadet
Thread starter
Joined
Jun 25, 2018
Messages
6
Appreciate your interest in this problem. This is exactly the pump I'm working with. The outside grommet on top of mount for the drive shaft, actually calls for adhesive. Once applied there is no way it won't mount properly. Looking at this pump as much as I have, I did notice cut outs on each side of the impeller. One on the bottom for the wear plate and a shallower cutout on the top. I did also place an O ring in the shallower cutout to help seal the top of the mount, to but to no avail. Thanks again.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Where is this water coming out anyway? There are large drain holes in the area of the lower motor mounts. Water is supposed to come out of those holes. In fact, a surprising amount of water.

When I first read your question, I assumed you were meaning it is coming out up above, just below the powerhead---not good.

Yes or no?
 

pfj57

Cadet
Thread starter
Joined
Jun 25, 2018
Messages
6
Water is traveling up the drive shaft and rolling over and out toward the front and down the mid section, under the power head. I had a guy check this out over the weekend, who is on a contract list for a local Coast Guard Station, and it was all new to him too. Just heard back this morning and after a call to Florida he got this: This particular motor is prone to water problems. Not lots of water but all the same they are leakey. My guess is the pump design itself. You can almost see inside the top of the housing and that grommet we talked about at the top doesn't make any contact with the drive shaft, it sits outside on a shoulder in the mount. That's why I tried an extra o ring on top of the impeller. Can't put an o ring at top of the mount because it won't make contact with anything to keep it pressed into place. Also to answer your question about the drain holes, the holes in this lower unit are about 1/8 round and forward and do in time drain most of the water out. I've put two OEM water pump kits in, 5001594, and deciphered information between 20" 25" and 30" shaft's and something other than a 60' V4. Thinking next year maybe something after market. For curiousity's sake the Stern Drive is P/N 90-305-60-20-95-06, small gear case with curved fins. Should be a Ficht motor. I should include that this motor has been a work horse. This was my Father in Laws boat and it's got 18 years of service and only had lower unit rebuilt once and highly maintained.
Had this running a good ten minutes or so Monday. No alarms and new t stats. I'm going to put it in the water over this weekend coming up, I believe all will be well.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Going to put it in the water this weekend???? You mean all this time, we've been talking about running on muffs? That may be the problem. Water hose pressure forcing through the drive shaft hole in the pump housing.

I've said it too many times to count--you cannot test a water pump by running on muffs. Under that condition, the pump is not pumping. It is only allowing hose water to pass through.
 

pfj57

Cadet
Thread starter
Joined
Jun 25, 2018
Messages
6
Okay and that is why I decided to post this on a board. For novices like myself and any other enthusiast's that like to tinker a bit and enjoy they're handy work. These post's hang around for years and there was literally nothing out there about this subject. Thank you again for your dogged determination for an answer. If this is the problem, or should I say unproblem, I'll be back at the end of the season to confirm. Finally an answer.............cool! Happy Boating all!
 
Top