Shift shaft height 1994 evinrude v4 140hp looper

jedwards353

Cadet
Thread starter
Joined
Mar 31, 2016
Messages
7
On 4/28/10 Faztbullet stated " 92-up v4/v6 crossflow/ loopers shift shaft height 22" 1/8.

http://forums.iboats.com/forum/engin...-compatability

I'm really hoping your correct as the boat I acquired (named in subject) has been slipping in forward. Making a thud as if it hit ground. I checked the height and it was close to 21.5. WAY OFF. I raised it to what the Johnson/Evinrude manual ( pdf download purchased online) recommended-21" 29/32 and it was much better but around 3500rpm started making the thud again. But still a major improvement. Question is.... Your recommendation of 22" 1/8... Is this the proper height in your opinion? And why is it different than the manual? But I hope it is correct because I'm goin to raise it a bit more on Sunday and hopefully it will fix my forward progress problem, reverse is fine by the way.
 
Last edited:

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Are you sure you have the original lower unit?-------Correct shift rod for the motor ?---------21-15/16"-----Shown on the list-----Time to have a look inside the lower unit.----
 

jedwards353

Cadet
Thread starter
Joined
Mar 31, 2016
Messages
7
Yes, all is original with the lower unit, which may be the problem, could need a rebuild. But, before going through all that just wanted to make sure everything else was in spec. Really curious as to the 22" 1/8 measurement Faztbullet listed.... Is that applicable to a 1994 90* v4 140 hp looper? Or is that to something else? Other option is to go to the local boat graveyard and get a used one for around $250-$300 and hope it'll last.
 

jedwards353

Cadet
Thread starter
Joined
Mar 31, 2016
Messages
7
Never mind my previous interpretation of the 22"1/8 measurement. That's what Faztbullet was referring to for the drive shaft measurement , which is what I think is on mine. Therefore, per the manual would put my shift rod height even further up to 24"7/16 if I'm interpreting the chart correctly. On the left of the chart it's giving shaft measurements ( I'm assuming drive shaft- measured from top of gear case to top of drive shaft) of 20, 22.5 & 25". Then the next column over it gives shift rod heights. 24"7/16 seems a bit tall for the shift rod but it has been getting better as I raise it. I'll take a look at it in a few hours but I'm still uncertain. May just go with a rebuilt or replacement lu.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The shift shaft measurement is to the centre of the hole with the clutch dog in nuetral.-------This should be easy !
 

jedwards353

Cadet
Thread starter
Joined
Mar 31, 2016
Messages
7
No Title

This is the chart
 

Attachments

  • photo240916.png
    photo240916.png
    815.3 KB · Views: 13

jedwards353

Cadet
Thread starter
Joined
Mar 31, 2016
Messages
7
I got the part on how to measure shift Rod height. Just confused on the chart. On the left it says "shaft length ". Is that the drive shaft?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
NO-----Shaft length is related to the transom of the boat.----There is 15" / 20" / 25" and 30"---------That is not related to the length of the shaft sticking out of the lower unit other then the fact there is a 5" difference between them.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
By raising the height of the hole you will get LESS engagement of the clutch dog.-------Caution ---study this and make decisions carefully as it can get spendy in a hurry !
 
Top