pre alpha to bravo 3

akcarver

Cadet
Thread starter
Joined
Apr 17, 2017
Messages
6
Looking for some help here. New to merc outdrives, not new to boating. All my previous outdrives have been volvos. I find myself with a 28' carver santa cruise that was originally powered with a pre alpha and a 305. I have a very low hour 350 merc ready to drop in it but I need to upgrade the outdrive. I found a low time bravo 3 a guy pulled out to go with a bigger diesel in his boat and I can get the complete set up cheap. It has 1.65 gears in it and I am not sure of the SS props. He had it behind a 270 hp diesel.
Question 1) are the transom holes the same for the pre alpha and the bravo?
Question 2) with this gear ratio what props would you start out with? The boat weighs 7200 dry
Question 3) will the bell housing from the pre alpha work with the bravo 3 or do I need to order one?
Question 4) The diesel used single exhaust and I know I would need to go dual on the y pipe. Thoughts on just ordering a new y pipe versus going with a lifted thru transom exhaust system? I have LOTS of room under the deck and can get in there and hold a dance if I wanted to so space and ease of working on the engine is not an issue. I wish all I/O installs have the room under the deck that this boat has. I would have busted a lot fewer knuckles and not need near as much rum or vocabulary to wee wee on the boat designers.

I have been searching the net for 2 days and my head is hurting from all the various searches I have done to find this info so I am hoping ya'll can take some pitty on me and help me out here with some straight answers.

Leni
 

Maclin

Admiral
Joined
May 27, 2007
Messages
6,761
Welcome aboard!

Why do you need to upgrade the outdrive? Just to get more current? Just curious.

I think the diesels have a much different ratio in their B3 outdrives than gasoline engines. For a 5.7 gas with B3 seems I remember the ratio is 2.0 . So my guess is you will have performance problems with that B3 from the diesel unless you can change the ratio. Hard to cover a 1.6 to 2.0 gap with propping in my estimation.

May make more sense to find an Alpha One setup and swap in. For that large of a boat with single engine I would look for a 1.6 ratio, used for 4.3's and such. If you want the B3 then I think you would need the 2.2 ratio, again due to just one engine in a 28 footer..

Good luck!
 

akcarver

Cadet
Thread starter
Joined
Apr 17, 2017
Messages
6
everyone I have talked to around here said the outdrive wouldnt hold up to the 350 for long. I live where we have the second largest tides in the world. The outdrive goes out and I am headed to hawaii before ya know it LOL. The boat came with the 305 from the yard and it was good for ~20-25 MPH I am not looking for speed, half the time its a nasty 4' confused chop so your not going anywhere fast. The B3 is available and it has 400 hrs on it. I can buy it cheaper than I can try to rebuild the drive I have and it should be more reliable. The hole shot should be better as well. The local dealer told me the 1.65 would be fine in it as the oil burner was a high rever and we are looking at ~ 10 hp difference. I don't have much faith in the local swindler so I wanted to post my questions here and hopefully get some real world knowledge.
 

Maclin

Admiral
Joined
May 27, 2007
Messages
6,761
Merc mates a 5.7 to a 2.0 in B3, so in your boat I think holeshot would not be better with that B3. Diesel torque curve is way different, "high revver" or not, and high rev is still only 4000-4200 I think. The HP is "all in" at much lower revs for the Diesel. I am just not sure you can make up that much gap with pitch, I think the lowest on a B3 set is 18p maybe? Also your boat is significantly more load to push than normal for a single 5.7 which is why I would even look into the 2.2 if you do not think an Alpha will last. And even with an Alpha I would try to go with a 1.62 ratio in your rig. When stakes are high as you mentioned, I would be worried the 5.7 would be tagged pretty hard with a 1.6 B3. You sure don't want to be lugging the new-to-you 5.7. But that's me :) Stuff to think about. I am sure more chaps will chime in soon so you can compare notes.
 

akcarver

Cadet
Thread starter
Joined
Apr 17, 2017
Messages
6
As I stated above I am used to the volvo OD so my terminology was not correct in the OP Question 3 should have been will the engine coupler work from the PreA to the B3. ?
Thanks
 

Scott Danforth

Grumpy Vintage Moderator still playing with boats
Staff member
Joined
Jul 23, 2011
Messages
53,418
the gear ratio is wrong for a gas motor. even the big blocks are coupled to the 2:1 ratio Bravo Drives. doubt they make props small enough. I think the 2.2 is uses for small blocks and V6's

you also need the bravo transom assembly as well since it is different than the Alpha drives and significantly different than your MC (there is no such thing as a pre alpha)

I would pass on this particular Bravo outdrive and get one suited for your needs or use a diesel
 

alldodge

Moderator
Staff member
Joined
Mar 8, 2009
Messages
44,770
Howdy

Correct if I missed something; your going from 305 to a 350, and a pre alpha to a B3. The B3 is coming from a diesel app.

IMO,
If the alpha is old enough you may need to drill two holes to fit a bravo transom assembly, and you will need a bravo transom assembly.

Do you know what the drive ratio was for the old drive?
 

JASinIL2006

Vice Admiral
Joined
Feb 10, 2012
Messages
5,768
everyone I have talked to around here said the outdrive wouldnt hold up to the 350 for long.

I don't really think this is true, unless you have a heavy and/or spastic right hand on the throttle. Lots of Alpha One Gen2s behind 5.7s and 350 Mags.
 

Maclin

Admiral
Joined
May 27, 2007
Messages
6,761
I don't really think this is true, unless you have a heavy and/or spastic right hand on the throttle. Lots of Alpha One Gen2s behind 5.7s and 350 Mags.


^^^^This^^^^

That was one of the first thoughts I had, hence questioned the want vs. need for the upgrade if the new engine is in "stock' Mercruiser tune.
 

Bondo

Moderator
Staff member
Joined
Apr 17, 2002
Messages
71,545
Question 3 should have been will the engine coupler work from the PreA to the B3. ?

Nope,.... Ya need to switch to Bravo, everything aft of the flywheel, includin' the coupler, 'n flywheel cover,...
 

akcarver

Cadet
Thread starter
Joined
Apr 17, 2017
Messages
6
Howdy

Correct if I missed something; your going from 305 to a 350, and a pre alpha to a B3. The B3 is coming from a diesel app.

IMO,
If the alpha is old enough you may need to drill two holes to fit a bravo transom assembly, and you will need a bravo transom assembly.

Do you know what the drive ratio was for the old drive?


I am 800 miles away from the boat right now but will be home later today and check.

As far as the rest... I am worried about the existing drive as it is a PRE ALPHA.. not an A1G2 etc. I have been boating and commercial fishing my entire life, I have watched boat after boat being shut down in the middle of the busy season because the older outdrives failed. I really didn't want to get into a philosophical discussion on why I am doing so, just asked if it would work and if SOME parts would interchange most notably would the transom shields swap out (same bolt pattern and this was answered). Other question thats burning in my mind is, will the engine drive coupler that was on the PRE A work with the B3?

The B3 comes complete, transom shield etc, engine back including pump. The guy is going to a jet setup in his boat and a larger diesel so anything that has to do with the outdrive install comes with it. I have a line on a sweet lil FNM 250 but its not a for sure yet. My back up plan is the 5.7 and I will put MPFI on it. I did that to a buddies 28' Trophy and it made a huge difference in both fuel economy and power delivery. It was super smooth.

The 5.7 is the norm on pleasure boats around here, there are TONS (as in a lot) of boats 28-32 that are running 5.7 engine (s) I have run them in several 28' boats and they do OK. We are not running 65 MPH boats, if I can get 20 to 25 I will be a very happy camper. If I feel the need to go fast I will do a day trip in my 24'CC hydrasport. This boat is only for longer multiple day trips that are just easy cruising and fishing along the way.

Thanks
 

Scott Danforth

Grumpy Vintage Moderator still playing with boats
Staff member
Joined
Jul 23, 2011
Messages
53,418
still doesnt address the issue that the B3 you have is from a diesel, so the gear ratio, coupler, and a few other things are specific to diesels and not a gas engine
 

akcarver

Cadet
Thread starter
Joined
Apr 17, 2017
Messages
6
still doesnt address the issue that the B3 you have is from a diesel, so the gear ratio, coupler, and a few other things are specific to diesels and not a gas engine

Correct.. Which is why I was asking what I needed to get ordered up. The FNM will bolt right up to this so I am leaning that direction if they guy still has it when I get home.


The top gears are the same 27/32 for 1.65 and 2.0. I can change the gears in the lo0wer end and still come out WAY money ahead from what just the outdrive costs.

Thanks for the replies, I will post up later when its done and running.
 
Last edited:

alldodge

Moderator
Staff member
Joined
Mar 8, 2009
Messages
44,770
I don't see an issue using the diesel drive. The diesel drive internal gears are cut to handle more torque. They are noisier due to the gears, but also stronger. Most of the bravo drives have the 32/27 gear sets in the upper, and changing the lower gears would be easy enough. The lower B3 uses standard gears, nothing special
 
Top