New points and condensers

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
I should have left well enough alone. Yesterday I took the plunge and put new points and condensers on the 1971 Evinrude 25102s. I had it running pretty well before the change. I got a timing fixture from Franks outboard tools and lined it up to the marks like its supposed to be. I put in the new points and condensers and set them accordingly. Wouldn't start. Readjusted everything and still nothing. No spark. Readjusted everything and then only to top plug. Readjusted everything and then spark only to bottom plug. Readjusted everything and then spark to both plugs. The marks on the plate and the tool are no where close to each other. Its right back where it was at about an inch and a half after TDC? Is this a normal thing? I wouldn't think it was.

But it does run. It also appears to have a lot more smoke blowing out of it. When you change out points and condensers do you then also have to adjust the carb and throttle linkage?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
No need to adjust carburetor after changing points and condensers if motor ran good before.-----------And using the timing fixture is the best way to time the magneto for peak spark...Please review that method as I believe you are making a basic mistake.---New points must often be cleaned.
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
Thank you raceone. I cleaned to points with cleaner and checked for any debris. According to the manual the new points are adjusted to .22 and are supposed to break open on the first mark. I have the index mark on the tool aligned with the index mark on the plate. I even used a multimeter check the thing and it shows that they are breaking where they are supposed to however the motor wont spark like it is supposed to. Moving everything over to where it was set before I swapped everything out it will fire up but very smokey and it just does not sound right. I have only run it in the test tank. It does not make since that it would run so far out of alignment like that.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Points are set with the meter to open between the 2 marks on the magplate.----The actual gap does NOT matter.-------Can't count how many times I have done this procedure and never a problem like you have at the moment.-----Is the top piston near the top of the cylinder when you are adjusting the front set of points?
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
I'll check on that. Thank you. I did note that there are newer coils than the original equipment so I know they were replaced at least once so i am presuming that the points and condensers were done also. I am under the impression that the plate can only fit on the shaft one way? Or am I incorrect?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The plate can only fit one way.---Cam that operates the points can be installed upside down.
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
thanks. the cam says top with what looks like proof marks on it also facing up.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
What are the points actually gapped at is it .22 most evinrudes are gapped at .020
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
.022 for new points according to manual. adjusting used points says .020 which is supposed to let the new fiber backing to seat.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Stop using the fixture set the points where it says set on the cam see what happens.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Points open with timing mark for each cylinder between the 2 vertical marks on the magplate.---Use your handy timing light to verify this !---Actual point gap does not matter.---Correct use of the fixture will get you the strongest spark each and every time !
 
Last edited:

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Start the motor and see where the timing mark on the flywheel is with a timing light.---Check both cylinders.
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
well using a dowel rod to check the pistons shows that when the fixture is aligned with the marks the 1 piston is topped out. However when I try to adjust the points the entire unit moves and it wont open them. It wont let me open them until is 1 and 1/2 inches past TDC. rotating the fixture to turn the crank 180 degrees the 2 piston is topped out but it will allow the points to be adjusted. Is my cam shot? I am perplexed.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You install the points and TIGHTEN the hold down screw for the points.-Then use that cam screw to adjust the opening of the points.-----Adjust them so that your meter shows them opening with the mark on the fixture between the 2 marks on the magplate.----Note---You may have problems if cam screw is fully seated down.-If so back that screw out one turn and try again.-Like I said I have done this procedure countless times.------Note---- you are removing the ground wire from the coil laminations when using the meter from that ground wire to the magplate I hope.
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
Yes sir, the points are isolated with the wires removed. On the bottom side the cam screw, the one that moves the points in and out, allows me to adjust them when the marks are correctly aligned. On the top side the cam screw keeps moving the entire unit back and forth? unless I move the fixture to 1 and 1/2 inches past TDC? It cant work like that I wouldnt think.I trust you raceone and know that you know more about this than I ever will.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Well it is the same lobe on the cam.-----Therefor I am going to say that something very simple is wrong here.----Factory parts or aftermarket ?----And good luck with the project.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Are you rotating the crankshaft to set the second set of points.---As I stated a basic mistake is being made and could be sorted out in minutes if motor was on my workbench !
 
Top