Johnson 9.5 won't idle or run.

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
This is a late 60's model. I have totally cleaned the top half of the carb and it will only run the the choke 3/4 closed. I had a old spare 9.5 and took off the top half of that carb and the same thing, after I cleaned that one. I have put new points and condensers in this motor. It's not like I have not worked on these old war horses before, but am stumped on this one. Usually a carb cleaning clears up this kind of problem. It has a strong water leak the I don't want to put a new gasket in as I have had these before and they run that way it seems. The leak is under the cowling near the recoil started and comes out of what I believe is the exhaust manifold. That would not make the engine run lean, would it? Any other possibilities?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
But the high speed jet is in the bottom half of the carburetor !!
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Needing choke to keep it running is classic symptom of a dirty high speed jet. (Yes in the bottom of the carb)
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Is it the little round cork gasket under the recoil starter top housing that is leaking? A simple job to fix it, so why not?
 

Sylva-Ranger

Petty Officer 2nd Class
Joined
Jan 17, 2016
Messages
167
Do you checked the throttle pick-up ?

​I remember an unadjustable 9.5 whit similar problem one time yhat seem to have an air leak, and i just synchronised throttle pick-up point and after that running well.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
OK, I will check the high speed jet in the bottom of carb. I don't think it is the throttle pick up advance but will check it too. Yes. I've read Leeroys a number of times. I think it is the large manifold gasket, I will check....I'll let you guys know what happens!
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
When you guys said the "high speed jet is in the bottom of the carb" I thought to myself? it is? As I have never noticed it there but in that round tower in the top portion of the carb. All that seems to be in the bottom is that strange plug/orifice that seems to just be a drain. I said to myself, Ok. I'll go along with this and took off the bottom of the downdraft carb that just seems to be a primitive kind of throttle plate before the reed assembly. There is no high speed listed in the diagrams at the parts houses either. In fact that jet in the tower is not shown or listed, probably because they do not carry that part. One guy on back forum pages here said you needed a special part to take that jet out. Is this true? Must be as it does not twist out like some. So I still have the same problem. It is not the throttle advance as it runs great with 3/4 choke at the same throttle setting and when you close the choke it does that lean cough nonsense and then dies.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Ok, wait, I guess we are dealing with terms or descriptions or terminology here. Yes, the high speed jet does come out of the bottom of the top part of the carb and then goes into a passage in the bottom part of the carb over to where the drain plug is. That passage blows thru and is not clogged. On the top portion of the carb there is a small hole "passage" that is connected to that main passage where the high speed jet is. IT seems to be not letting any air thru, but I poke it with a carb cleaning wire cleaned and nothing changes. I have ultra sonic cleaned this dam thing for 30 minutes and I don't think it is still clogged. On the other top of the carb I tried on this motor I took out the small aluminum plug that leads into the passage that has a pipe that sprays the gas into the venture. That size plug seems hard to get and I have many plugs from other engine carb kits and none fit it. Too large or small.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You need to accept the fact that the high speed jet ( aka orifice plug ) is in the bottom of the carburetor.---All the fuel for low speed and high speed operation must go though it.-----So make sure it is clean !!!
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Ok, then, if that is the jet, it is clean! I also took out the large aluminum plug with the 3 idle holes and they have been checked and clean also. I have sealed a new plug with High temp pematex red (which seems to do as good of a job as the other brand that has 3 numbers) and we shall see if it now runs. For those that might not know, you can check carb passages in a dim room with a flashlight. If you can see light in the passage when the light is shined at the other end, it usually is clean. But not always, but especially after a good clean. But at least you will know it is not totally obstructed.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Well, sad to say, no go. It still runs great at 9/10's choke but does loud coughing if choke is opened. That carb is clean and I think it is something else. Guess it will go in the parts motor graveyard unless someone that knows these motors real well chimes in.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I have a bunch of these motors.-----Got the last one " gratis " because flywheel would not turn due to one loose screw in maneto.-----Worked on many of them over the years.-----But I am not standing beside you as a coach and that may be the problem here.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Yes, these are great motors. I think OMC kind of made a mistake with the next generation 9.9/15 with the overbuilt lower unit. The old 9.5 was only 60 pounds or as the old advertising said " Power of a 10, Weight of a 6 and size of a 3 " The front shifter was ahead of it's time and the fold down handle make them fit more easy in Northern bush airplanes or what have you. Some complain of inadequate power, but tuned right they have a lot of torque. They are also 1 inch shorter than any other outboard and I have planed in very shallow water with a couple people in a 12 ft. Jon boat. Kind of loud, that's why I call them the Harley Davidson of small outboards. Loud but a kind of good sound to them. They seem to use more gas than the 9.9/15. I had a couple of Tohatsu 9.8's that are light at around 56 lb., the lightest of the light for this portable category of outboards. But there is no comparison to even the 9.9 OMC when it comes to torque and raw power. And the 15 at 74 lb. blows the Tohatsu 9.8 out of the water;;; literally.
 

Crosbyman

Admiral
Joined
Nov 5, 2006
Messages
6,298
sorry no offense....


​runs ok with 3/4 - 9/10 choking.... so it wants less air in to be able to suck in more gas.....to run or there isn't enough gas to being "naturally" sucked in

​vent open ?... of course
does it run any better if you choke less but while pumping the fuel pump ?
fuel pump running ok ? fuel pump filter clean ?
all hoses to/from the pump checked for obstructions, flaking, crud etc....
​tried a different tank and/or hose ?
​any possibility of and air leak inside the engine..... reducing the suction effect of negative pressure in the crankcase to pull in its gas ? (seals ?)
​reedds checked ?
​try bagging/wrapping the carb body thightly with cellophane plastic to close off any air leaks into the carb body itself

​beg borrow to try a new carbo

​good luck chasing this bug
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The carburtetor has been discussed here.-----Often the novice picks on the carburetor as step # 1 in fixing a motor.---What other trouble shooting if any has been done ??----Perhaps post exact compression values .----Perhaps tell us if spark will jump a gap of 1/4 in free air.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
It seems like you refuse to remove the high speed jet (orifice plug) for cleaning and inspection. How do you even know it has the correct one in there? They come in a multitude of sizes. Yes, you are supposed to use the special screwdriver to get it out. Trying to make-do often buggers it up, making it impossible to get out.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Thanks for a good helpful post!!! I will slowly check out all of these things. Vent is same I use for other outboards that run fine recently, so I can eliminate that. You know, it could be that old style fuel pump that is on there. I will check. IT does have old hard fuel hoses I thought about changing. This outboard does suffer from "old" in general. Reeds seem Ok just from visual inspection from the top. I have considered air leaks in the engine and was waiting for someone to suggest that to bolster my guessing on that. Yes, tried a different upper carb body...same thing. Wow, never heard of wrapping the carb body in plastic. Some might like to know that an old Northern bush trick if you are low on gas or have a heavy load is to wrap a burlap bag around the cowling of an outboard. What>? Yes, it lets the carb suck in water vapor that makes it run more efficient.
 

Crosbyman

Admiral
Joined
Nov 5, 2006
Messages
6,298
plastic wrap is just a wild shot..in case an air leak somewhere into the carb body prevented crankcase vacum from doing its job


I once got stranded when my pump on the hose suddenly split lenght wise preventing gas from the tank being sucked up out of the tank. to the engine


​solution.... I wrapped the pump with plastic wrap out of the lunch box sealed it up with tape.at both ends and around. got me back to shore !!


​ meantime follow the leads from experts like FR and racerone clean that carb....again
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Checked out the fuel pump with the hose off and running. A normal amount shot out of the hose. In fact, when I opened the choke up even more of a stream shot out 4 to 6 feet. Yes, that is funny how necessity is the mother of invention. An old northern Indian trick along the 1000 mile Yukon river is if you blow a head gasket, you cut a section of bark from a Birch tree. It makes a wonderful "Skookum" tough gasket that will last as long as a real factory one. I learned that one 40 years ago. The one thing I hate about these motors and the 9.9.15 is that lame recoil starter. I have taken many apart and still hate it. I hesitate to take out the one on this motor to fix the water leak, but will probably do it. It will probably come unwound or fly apart or.... they are weird starters so that they can fit in the pancake motor cowling. Yes, I will check compression again and spark. Both seemed good enough before
 
Top