johnson 88 special won't idle

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I just picked up this 1992 Johnson 88 special in good shape. J88MSLCER I cleaned the carbs and it will start but not idle. I'm thinking timing? I fooled with the cams and I guess what is the idle cam, but it seems they have to be way out and it still will not idle. I have it in a tank and cannot throttle it in gear but I put a wire on the 2 throttles on the carb to make it run. Any help would be greatly appreciated!
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The motor is NOT a 92 model !----The model # makes it an 89 version !------Start with a compression test first.
 
Last edited:

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
The idle rpm is set by adjusting the idle timing. Set the idle to between 650 and 750 rpm's. The idle must be set when the boat is floating normally in the lake, and is shifted into forward gear. Can't set it on the trailer. If you just can't get it to idle, you may need to pull the carbs apart and clean them. Esp pay attention to the idle circuits of each throat. Be sure to pull all the jets out for cleaning and visual inspection.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
OK, so I tested compression and it is good at very close to 120 for all 4 cylinders. It runs fine with a extension wire attached to the throttle butterfly valve rod, but seems to die if not kept at fairly high rpm. The spark must be good for it to run so good at medium and high rpm. When we try to restart it, it is flooded and only by drying the spark plugs will it start again. It blows a lot of smoke, but yet, the ceramic on the spark plugs is totally white, no brown or black. Sometimes it seems the fuel tank bulb has to be squeezed a lot to get it to start, other times not. I thought it might be the fuel pump, but, again it runs, but maybe that is why it stops? I so far think I might need to clean the carb again (soak it this time) to get those idle circuits cleaned out. The first time I cleaned the carb, it idled for a short period of time. Maybe some junk got rearranged in there and plugged it up again? The motor is in good condition, probably with only a few hundred hours. Not dirty with oil and rust etc. I have purchased a CDI from E-bay (new) and when it gets here after I clean the carb, install it. What do you guys think?
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
Why did you purchase the CDI unit, was there another issue too.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
When you cleaned the carbs did you take them apart and remove all the jets and whatnot?
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Sounds like you need to go through the carbs properly and then preform a link and synch as laid out in the manual.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
One guy on this forum in the 88 forum said that did it for him, the new CDI, so that is why I bought that. I just purchased a rebuild kit as one carb or 2 might be flooding due to a worn float needle, we shall see! No, I did not remove the jets as they seemed hard to remove, but will this time. Are the idle jets in/on the bowl plugs? Could this be related to the shift/throttle black plastic adjustment wheels? One person said that was a simple fix for him. One guy said the CDI takes care of the timing. Is this true and no other timing adjustments needed?
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
At this point nothing you've mentioned indicates a timing or CDI issue, sounds like dirty carbs. The only way to clean the carbs is to totally dismantle them and clean every piece, then sometimes you need to do it again.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
You also indicated that you messed with the linkage. After going through the carbs completely and properly you will need ti find a manual. Do the link and synch procedure.

The cdi does not exactly control the timing. Thats more in the initial set up of the linkage and the link and synch. Running with improper timing can drstroy motors if its wrong enough. That happens when folks mess with the linkage thinking it looks like an idlr adjustment when what you are really changing is the base timing.

I would stop listining to.the guy that said the cdi sets timing. Not really the case. At least not as far as the timer base is concerned.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Sounds like good advice gentleman!!!! THANKS!!!!!! HAPPY 4th..........
 
Top