Johnson 115 1997 Ignition Circuit Problem

Chip884

Cadet
Thread starter
Joined
Jul 16, 2016
Messages
15
I do have a battery isolation switch. I checked and cleaned the connections at the battery, battery switch, and at the solenoid. There are two positive wires that go to the engine wiring harness that were also cleaned and checked. Next is to check the connectors in the engine wiring harness and those that connect to the wiring harness that goes forward to the instrument panel.
 

Chip884

Cadet
Thread starter
Joined
Jul 16, 2016
Messages
15
While checking wiring connections in the bilge, I found a green (ground?) wire laying near the fuel tank not connected to anything. I'm thinking it's meant to be connected as a ground for the fuel tank. Is it common to have the fuel tank grounded similar to how the fuel fill port is grounded for static charge dissipation? It certainly would seem logical.
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
I checked and cleaned the connections at the battery, battery switch, and at the solenoid.
Did you check them with your voltmeter with the key in the ON position?
At some point along that cable the voltage will disappear, you know it's got 12V at the battery but nothing at the solenoid.
(My money is on the isolating switch but test with the voltmeter before cleaning up so you know where the problem is.)

You will have to trace the mystery green wire to see where it comes from.
 

Chip884

Cadet
Thread starter
Joined
Jul 16, 2016
Messages
15
Found the problem. At the engine their is a deutsch connector for all the wires that come from the key switch. On the engine side of the connector I?ve got 12 volts. Ran a long jumper from battery wire socket in the connector to the key switch and everything works - gages, starter, choke. So the problem is either at the pin side of the connector or a broken wire between the connector and the key switch. Ordered a new deutsch connector. If that doesn?t solve the problem, I?ll be running a new wire to the key switch.
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
Good news but you did say there was no power at the solenoid positive.
 

Chip884

Cadet
Thread starter
Joined
Jul 16, 2016
Messages
15
Sorry for the confusion...12 volts is present at the solenoid's positive battery cable connection stud. 0 volts at the solenoid's positive connection from the key switch (red-yellow wire). 0 volts at that point because no power was getting to the positive (battery) connection at key switch because of the faulty (red-purple) wire or bad deutsch connector in the engine harness. If the new connector does not solve the problem I'll be pulling a new wire.

Thanks to everyone who helped with this, I sincerely appreciate all the input!! Maybe I'll be able to get back to fishing before the ice arrives. Chip
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
I think you can replace individual pins & sockets inside those deutsch plugs, hopefully someone will chime in.
Not impossible but it's highly unlikely to be a break in the wire along it's length so fully check the connections at each end & the plug itself.
 

Chip884

Cadet
Thread starter
Joined
Jul 16, 2016
Messages
15
Picked up the new deutsch plug at noon and installed it - same problem. Pulled a new wire under the deck, made connections, fired it up, runs like new. Going fishing tomorrow.

Thanks again!!
 

Chris1956

Honorary Supreme Mariner
Joined
Mar 25, 2004
Messages
29,328
I have nearly the same motor. I found melted wires in the engine harness at that Deutsch connector, as well as under the dashboard, at the gauge connections. In my case, the tach wire was broken, and the fused power wire would short to ground, occasionally. I spliced in some new wires, and the issue was fixed.
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
I'd probe the wire (red & red-purple) from the solenoid where you have power, out to where the power disappears.
Google 'multimeter needle probe'.

It may go through another connection or fuse that I'm unaware of, as said it's not impossible to have a break in the wire but highly unlikely.
 
Last edited:

Chris1956

Honorary Supreme Mariner
Joined
Mar 25, 2004
Messages
29,328
In my case the tach signal wire was melted and shorted to ground. If the OPs issue was the same, I would expect the 20A fuse above the starter solenoid to blow, as the ign power tot he starter solenoid should blow that fuse.
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
I looked up a circuit for what I believe is a 1997 model and it looks like there's a distribution box between the solenoid positive (the one with the battery positive on it) and what I call the 'big red plug'.
I'd definitely needle probe the appropriate wires until I found the actual problem.
 

Chris1956

Honorary Supreme Mariner
Joined
Mar 25, 2004
Messages
29,328
The "Big Red Plug" was used on earlier models. He has the Deutsch connector version of the wiring harness. However,to your point, the troubleshooting procedure is the same.
 
Top