Evinrude 70 fuel problem

petersbc

Seaman Apprentice
Thread starter
Joined
May 19, 2013
Messages
38
Been having issues with this motor 1977 evinrude 70(70773S). The latest issue is not wanting to idle when in the water. I rebuilt the carbs a couple weeks ago when I was having an issue with transitioning from idle that was worked around by tapping the choke. That problem is fixed. I started looking at ignition because the carbs were rebuilt and I had a problem with loosing a cylinder suddenly on one trip. The ignition has good strong spark and good ohm and DVA readings so my thought was reeds.

I pulled the air box to look for fuel spit at idle and found none but found something else. #3 (that's the bottom cylinder right?) is running very lean. I was spraying carb cleaner around looking for vacuum leaks when I didn't find any I shot a small squirt down the carb. On #1 and #2 it caused the motor to stumble but on #3 it changed the engine note but the motor seemed to speed up slightly. I then disconnected the choke linkage so I could close them independently and when I close #1 or #2 the motor stalls (#2 stalls quicker than #1). #3 just causes the motor to smoke a bit more and changes the exhaust note but the motor will not stall no matter how long I hold it. When I pull a plug wire on #3 the exhaust note changes so it is fueling but clearly not enough. This is a serious issue but I'm not sure what could be causing it. There is nothing to the carbs just some plugs that cover machined passages two jets and a float bowl. I cleaned them thoroughly and blew everything out with air. The needle and seat was changed as was the float. I inspected all passages to make sure they were clear before setting the new plugs and putting them back together. I set the float height per the instructions in the carb kit (sierra)

Any advise on determining if the carb is working after I take it apart again? I suppose the float could be stuck closed but I checked it by blowing through the fuel inlet before they were put back on and they all opened and closed as they should.

Any advise would be greatly appreciated.
 

petersbc

Seaman Apprentice
Thread starter
Joined
May 19, 2013
Messages
38
Re: Evinrude 70 fuel problem

I was advised that there is trash in the carb so I pulled it off and blew it out without taking out the core plugs as I didn't have a kit. I captured the fuel and inspected everywhere I could before starting and there was nothing to blow out. I captured all the carb cleaner anyway and it had nothing in it. Put it all back together and I have the same problem. If I cover the carb opening with my hand I feel the suction and my hand gets wetted with fuel but the motor does not stall. Same thing with #1 but I can stall it with the coke. #2 dies almost immediately and has the strongest pull. I back to thinking reeds.
 

petersbc

Seaman Apprentice
Thread starter
Joined
May 19, 2013
Messages
38
Re: Evinrude 70 fuel problem

I think I found the issue.

I was talking to a friend about this problem and he said "looks like #2 is doing all the work". That made me think of the Goldwing I had that had four carbs. To balance that motor I used a manometer hooked up to each cylinder and adjusted till the vacuum was equal at idle. That's not possible with this motor so I decided to use the choke test. I "resynced" the carbs by the book and the problem seems to get better. #3 (bottom) still would not kill the motor but had a bigger affect when choked. I took it one step further and slightly cracked #1 and #3 then tightened down the linkage and now all three cylinders have the same affect when choked. Idling on the muffs at 1000 each cylinder when choked causes the motor to load up a bit and slow down but none kill the motor completely. This seems balanced to me.

I need to set the timing and the throttle linkage and then lake check it.
 
Top