evinrude 15hp Help!

superfluke82

Cadet
Thread starter
Joined
Jul 1, 2017
Messages
7
I'll tell whole story and what ive done to best explain where im at.

My neighbor has 1975 evinrude 15hp model 15504C. he's had it for a year and it ran great. The motor began to lose top end and wouldnt idle at slower RPM. Before i began to work on it the motor would start first pull but only idle at high RPM. When boat was in gear it would not throttle up much but it would run consistent no sputtering or surges.

1)I removed carb which seemed to have a small leak from bowl but carb looked good. I cleaned it good and rebuilt it with kit.

2)Fuel pump was full of crap and wasnt working right. I replaced it

3) New fuel line with new clamps and filter added inline.

4) new spark plugs added which were recommended for that motor

5) compression is 95 in both cylinders

6) roller ram on carb is rigged with a drywall screw. but it appears to line up well with timing base and base moves well

7) stop switch is disabled

Motor will start but only run at high rpm. motor starst to die some until i tap throttle and it'll go back. Boat in gear still does same thing and wont go much higher that high idle. I have idle knob set on 2 turns out. Bottom cylinder has alot of unburned fuel and oil in it

Ive looked motor over more and have realized the block has a model number 10R78M. motor has a power pack (which has manufacture date of 2014)and new looking coils. Carb is for a 15HP.

I have no clue where to proceed. Is there a way to tell if 10R78M was converted to a 15? doesnt it need a different header and reeds?
I can post pictures just let me know what you need picture of

Im sorry if i got confusing
 

superfluke82

Cadet
Thread starter
Joined
Jul 1, 2017
Messages
7
just looked up power pack it's not even for that motor. it's for a 1985+ year motor. It's a CDI 113-2285
 

OptsyEagle

Lieutenant
Joined
Sep 13, 2006
Messages
1,367
There is no power pack on that model. It is a points and condenser type motor. I would run a cylinder drop test to confirm if both cylinder are working. I would also do a spark test to verify that both cylinders are receiving spark and the spark is strong enough to jump a 3/8 inch gap. I would also get rid of the recommended plugs and use NGK B6HS. That model of motor is very finiki on spark plugs. If you search this site or go to Leeroys Ramblings you will see the problems people have had using Champion spark plugs and most have found better success with the NGKs. It has something to do with the design of the head and the way the fuel comes into the combustion chamber. Anyway, I have the identical motor and mine only runs properly on NGK spark plugs. B7HS are OK and will be fine for the 9.9HP but the 15HP issues are exasperated by its larger carb throat and I find the hotter B6HS plugs work better for my 15Hp

Anyway, do the cylinder drop test and spark test and let us know how she does.
 

RCO

Petty Officer 1st Class
Joined
Jun 15, 2016
Messages
350
Someone has either swapped the powerhead or the transom bracket. The 75 would have low tension magneto ignition, where the 10R78M model would use CDI ignition. Same powerhead between the 9.9 and 15 as long as everything else is correct it should work fine.
 

superfluke82

Cadet
Thread starter
Joined
Jul 1, 2017
Messages
7
is there a easy way to test powerpack for a weak spark? or test sensor and charging coils are working properly? I did resistance test on sensor, charging and ignition coils and passed
 

AlTn

Commander
Joined
Mar 9, 2010
Messages
2,813
10R78M is a 1978 9.9 hp w/cd ignition..may have been converted to 15 hp...testing..if 1 cylinder has spark then both the sensor and charge coil are working..if spark on one cylinder and none on the other, swap the coils, does the spark follow the good coil?..if so, you have one bad coil...if not, then the likely culprit is the power pack...make certain that all the ground wires for the coils and power pack are are making good contact before testing
 

superfluke82

Cadet
Thread starter
Joined
Jul 1, 2017
Messages
7
I realized i got side tracked when i did drop down test and never completed it. it would of saved me a day of aggravation. found out top ignition coil went bad. replaced and running like a champ now
 
Top