Electrical difficulties

paddlefaster

Recruit
Thread starter
Joined
Aug 3, 2012
Messages
3
Boat has a two battery trolling bank and a cranking battery. I replaced the battery conections on the + sides of both trolling batteries. They are wired: stern batt + to 12v leg of trolling motor bow plug & bow batt -, stern batt - to ground. Bow batt + to 24v leg of trolling motor bow plug, Bow batt - to stern batt +.

The cranking battery handles everything other than trolling motor. That I know of, I have done nothing to the cranking side circuit. I now have zero function from anything on the cranking side!! Other than trim and fuel gauge function when key is turned to run. Motor won't crank, one light from one of the switches on main switch panel will illuminate after being on for a couple min. I have 12v on both sides of each breaker on the breaker panel.

Am I having a ground issue??

I removed all three batteries last night to have them tested this morning. Cranking came back fine, 1 trolling came back bad, 1 needed a charge.

Thanks for your help. I hate for this to be my first post.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Electrical difficulties

He has a 24 volt troller system. No way to charge two batteries in series from a Perko switch. Since the problem is on the engine side, without going through the battery cable and terminal cleaning followed by circuit testing it's tough to say what's going on. It is odd that the trim still worked but the engine wouldn't crank. If the fuse under the engine cowl is blown then the trim typically doesn't work either. The switches at the helm are not powered via the engine harness so that's a separate issue. Gauges are powered through the engine harness (from the "A" terminal on the ignition switch) so check for power there. There are typically two #8 or #10 wires (red & black) that run from the starting battery to the helm (fuse panel). That circuit is the "boat" circuit so a bad connection in either the POS or NEG line at the battery, in-line fuse or breaker, or at the helm would account for the switch issues.
 

paddlefaster

Recruit
Thread starter
Joined
Aug 3, 2012
Messages
3
Re: Electrical difficulties

He has a 24 volt troller system. No way to charge two batteries in series from a Perko switch. Since the problem is on the engine side, without going through the battery cable and terminal cleaning followed by circuit testing it's tough to say what's going on. It is odd that the trim still worked but the engine wouldn't crank. If the fuse under the engine cowl is blown then the trim typically doesn't work either. The switches at the helm are not powered via the engine harness so that's a separate issue. Gauges are powered through the engine harness (from the "A" terminal on the ignition switch) so check for power there. There are typically two #8 or #10 wires (red & black) that run from the starting battery to the helm (fuse panel). That circuit is the "boat" circuit so a bad connection in either the POS or NEG line at the battery, in-line fuse or breaker, or at the helm would account for the switch issues.[/QUOTe

No switch.

I haven't gone through the engine harness yet or checked the fuses under the cowl. That will be my next step. The motor connections looked good at the battery. Frustrating that working on part of the system "unrelated" to the cranking side has caused it to stop working.

Thanks!!! Keep the replies coming!!
 
Joined
Feb 17, 2012
Messages
2,906
Re: Electrical difficulties

cranking battery ground goes to engine and ground buss? picture would realy help.
where does the trolling batterys ground to? (trolling motor or somewhere else)
you do not have a dual switch that selects a-b-both? (if you do whats it set on)
do you have a volt meter and can you check the ground up under the dash to the battery post?

my guess is you have either missed a wire or pulled a wire off a terminal strip or like silvertips said its a bad connection.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Electrical difficulties

Trolling motor batteries don't ground to anything. A troller typically has a positive and negative lead just like any other electrical device. 12 volt units hook to the positive and negative posts on the battery. No need to ground the battery anywhere. I would place a fair wager that whatever you did on the troller side was not the cause of the problems on the engine side.
 
Joined
Feb 17, 2012
Messages
2,906
Re: Electrical difficulties

i agree with what you are saying sivertip but on my boat its diffrent as i have a emergency perko switch and theres no telling if someone has bugged the wrong ground wire which is why i find it intresting that he says he grounded the stern - to ground instead of saying he hooked up the trolling negative. still thinking he pulled a cable that a ground wire was tie wrapped to and ripped it off the buss but with out a picture thats realy a wild arse guess anyway
 

paddlefaster

Recruit
Thread starter
Joined
Aug 3, 2012
Messages
3
Re: Electrical difficulties

i agree with what you are saying sivertip but on my boat its diffrent as i have a emergency perko switch and theres no telling if someone has bugged the wrong ground wire which is why i find it intresting that he says he grounded the stern - to ground instead of saying he hooked up the trolling negative. still thinking he pulled a cable that a ground wire was tie wrapped to and ripped it off the buss but with out a picture thats realy a wild arse guess anyway

Appologies, the stern batt - IS hooked to the troller ground.

The wiring in the console is a cluster, I would not be able to get a picture that would be useful as a diagnostic tool. I cleaned terminals on the cranking side, went over ground buss bar, and installed cranking battery. She cranked and accessory panel is working as it did before!

You would think I would have learned by now to check EVERY connection (I drive an electrically challenged 99 dodge cummins). I've had the boat almost a week now. Plan is to get the trolling motor running then start sorting the misc wiring in the console that appears to be part of old systems that are no longer in place. I would, if possible, like to wire a switch to be able to use the trolling bank as a cranking battery should the need arise. Thanks again for the help!
 
Top