'97 175hp carb setting

Rainman57

Recruit
Thread starter
Joined
Feb 5, 2012
Messages
3
I recently bought a boat with a ?97 175hp Ocean Runner on it. Sat for at least 6 months, maybe more. He (previous owner) wasn?t very astute about understanding how to care for an unused engine. So, I?ve been working on bringing it back to life. Spent 3 weeks doing cosmetic hull work, and just getting it back in the water. Low speed idle in gear has been an issue since day one.

Fuel has also been an issue. Both what was in the tank, and what I can get. Drained it down as far as I could. Replaced spark plugs, thermostats, and water pump. Decarbed with OMC engine tuner on the muffs just before putting it back in the water. Replaced the existing fuel filter with one of the Racor?s with the clear sight glass in the bottom. Water has definitely been an issue. I live in the Cayman Islands. Quality is not their forte?drain some sludge out of it pretty much every day?

Filled the tank with fresh fuel at the local pump. You don?t want to know how much I paid for it?

Ran about a ? tank on Saturday with no problem. Sat on Easter Sunday because it rained all day, and took it out Monday. Started having low RPM problems pretty much from the getgo. Runs like a raped aped from 3000~4500 rpm. Not opened it up to WOT yet, so don?t know what top end is. Want to get the lower range worked out first. It?s a fishing boat. And performance at trolling speed is paramount. Below 1200 rpm, it coughs and sputters, then dies. Starts right back up for the most part, with occasional over-revving. But have read that may be a de-carb process. Will defer that for a few more outings.

Sooo?

Just bought rebuild kits all for the carbs. Got the first one done. Been other post thinking these carb don?t have idle speed adjustment. A while back I pulled a carb off, and would have thought the same thing.

But tonight, while I pulled the first one off, I saw a screw I missed the last time I pulled one off. They?re not in the carburetor, they?re on the throttle plate. I missed that.

Shades of synching a pair of Holley Double Pumpers on a big block Fords in the 70?s comes to mind?

With those, the initial setting was 1 ? turns out from bottom, and play it by ear. I can do that?

Bottomed out that first carb by finger (have to go get the right size tool tomorrow) before I pulled it off, and it seemed to be about 1 ?.

Anybody got a suggestion for the initial back off on the needle valve? I saw a post somewhere that said 9 turns...???

That's just not anywhere close to consistent with the first one I pulled off the throttle plate.

Appreciate any help in advance...
 

bob johnson

Rear Admiral
Joined
Feb 25, 2009
Messages
4,306
Re: '97 175hp carb setting

I have a 1997 manual at work..i can look at what it says....I have a 95 a 96 and a 97 ocean runner/pro in V4( the book covers 90 105 115 150 qne 175 60 degree loopers( the 95s didnt have the 105hp's)

I know that from 95 to 97 the settling to back out in number of turns doubled almost!!

bob
 

Rainman57

Recruit
Thread starter
Joined
Feb 5, 2012
Messages
3
Re: '97 175hp carb setting

Thanks, Bob

Starting to realize why the thing isn't running worth a darn at low speed. Wasn't able to get a count to bottom the first carb because i had to take out the idle adjusting screw to take to the hardware store to get the right size hex wrench.

But the second one was out to about 10 turns. Third was at right at 5~ 5 1/2. These were port side top to bottom. Top two floats and needles didn't show much wear, but the bottom float was way out of adjustment, and the needle had noticeable wear/deformation. The old needles were the rubber tipped type. The rebuild kits are SS needle to brass seat.

Haven't had the boat very long, but noticed the fuel line wouldn't hold pressure very long. Thinking this float may have been one of issues in that regard. Will have to see what the rest of the carbs show...

Haven't rebuilt it yet, but the bottom starboard was at about 8 turns out. ???

One of the things I noticed is that the screws seem to bottom out the spring before they seat the needle. ???

Might account for the variance. I won't drive those screws up very much. Not going to stress anything at the risk of damaging the seat in the throttle plate..

But seems like that is going to make getting things sync'd up somewhat problematic...

Thoughts? Suggestions???

Or do I just figure on taking a buddy to drive the boat and a wrench and screwdriver and use that old fashioned (circa 1975 hot rod big block Ford with Holley double pumpers) ear and mess with it till it works...???

Next post...timing
 
Top