85 Johnson Won't Stay Running

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
And if everything is okay there? I'm thinking I may need to test my power pack but I'm not sure
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
gotcha! I am tired of renting these tools time and time again so I'm finally biting the bullet and buying them all...remote starter switch, adjustable spark tester, and compression tester. should have results tonight!
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
Alright SO....after the tests I'm still stumped. Compression read as follows
CYL1: 110
CYL2: 110
CYL3: 105
CYL4: 110

Yes, the 105 is a mystery to me but not nearly enough to cause any issues. Good spark on all cylinders, allthough I DID find that the coil on CYL3 was firing maybe 1/5 of the time...i thought this was my smoking gun! I switched it for a good coil, tested it, good AND CONSISTENT spark, but it's still sneezing and cutting out HARD. Won't idle right now...let me know what I should be looking into next. I'm thinking i need to test the power pack but again, I don't know a lot about these engines...thanks in advance!
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
https://drive.google.com/open?id=0B62Fyxg1VzwYbElCRWw2aTZwUWc

So here's how it was running earlier...will idle all day, but the second you go to give it any throttle it cuts out HARD. Not like a fuel stumble, but like a total loss of spark or something....10 minutes after this video and letting it idle for said 10 minutes, it went upstairs with and without a load perfectly...
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
compression numbers look good.

Based on the video, it looks to me like the remote throttle isn't having any effect. Is the cable slipping?
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
No the remote throttle works well, but the only way I can get it warmed up enough to run right is by revving it back there without a load. If i try using the forward controls (putting a load on it) it dies out
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
I've been doing some reading and something kind of dawned on me...yesterday when doing spark tests, checking gaps on plugs, etc, the two top plugs were pretty badly oil foiled, whereas the bottom looked like they were OK. I'm wondering if maybe this indicates a rich condition in the upper carb? Float level off? Also after doing some reading I may up my idle speed a tad and see if that helps. thanks again for the great responses, especially you oldboat1
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
Sorry to somewhat spam the thread but I'm trying to keep this thread as updated as possible...today my dad was by the house and he was looking at it with me. After I took the front of the carb silencer off, we realized that the sneeze is ONLY coming from the bottom right cylinder (this is looking at the motor from inside the boat, cylinder 4). I cleaned the main and idle jets again and honestly did see some improvement...but all the cranking has just about fried my starter. Think I'll be getting it overhauled, cleaning the jets again, and taking another crack at it.
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
UPDATE, actually need some advice here now. So after work I came home and got it running. I did some research basically all day at work and was reading about the timing advance on these motors...I didn't think this could affect my idle at all. Well sure enough, I watched the action on my timing advance and it won't budge when I put the controls at full throttle...thus why it won't go upstairs! I lubed it and it moves much better now but won't move with the throttle as it's supposed to. I noticed that if I moved the lever forward just a tad, it got the timing perfectly at 0 degrees and the sneezing completely stopped!! So my question is...how do I adjust this assembly? i want to move it just a tad so it's a bit more forward at idle. Then I'll worry about taking the flywheel off and getting it moving better...anybody know what size that huge nut is? 114 was too small, 112 too big. Didn't have any sizes between around the house. Here's a picture of said assembly, thank you guys in advance!!

https://drive.google.com/open?id=0B62Fyxg1VzwYaWtmSVpaODJlWnc
 
Last edited:

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
might be wrong, but think you would not be able to move the throttle lever at the remote unless the timing plate was rotating, linkage broken, or a problem with the cable or box.

Anyway, if you suspect the timing plate is sticking, that would be a place to start. If you aren't ready to take off the flywheel and have at it, you might try spraying some WD-40 up underneath and try moving the plate by hand (or continue trying). The motor would typically need to be in gear to fully rotate the plate. It's usually a buildup of old grease, and you may not be able to resolve it with disassembly, but if mine I would try it.

By moving the plate, I mean reaching up under the flywheel with both hands, and rotating it.
 
Last edited:

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
The arm that moves the timing arm is spring loaded, no? If the timer base is stuck with old grease, the spring won't overcome the tension of the old grease. Good thought on the WD-40 ob1 (kenobe), it's the perfect solvent to re-activate the old schmutz that's in there. Best to remove the flywheel though - clean and re-grease. Torque the nut properly to 100-105 lb/ft with clean tapers on the crank and flywheel.

For advancing the timing, you just use the idle adjust screw, but your picture shows it's well off the rest now. Look up the 'link and sync' procedure in the sticky at the top of the forum page.
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
Yeah I hit it with some high strength penetrating oil and moved it using the arm, it did free up a bit but not enough for it to work properly...as for the link and sync- I will go ahead and read up on the procedure. I'm not afraid of taking the flywheel off by any means, just confused on what size the nut is? I'll have to look around a little more and see what bigger sockets O have laying around. Also yes, it is spring loaded, but when I move the control to full throttle, the timing advance only moves a little, not to its full stopping point as it should. I wasn't sure if the linkage was broken or if the timing adjustment just wasn't sliding well enough for it to work properly...how can you tell it's way out of adjustment by the way? How far the arm is from the stop? Appreciate the wise words guys, cheers!
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Nut is 1-5/16" from what I recall. I had a 34mm socket that worked.

The timing 'stop' is just that. The advance arm should hit it when the throttle is advanced past about 2/3. Typically the timing is set when the motor is new and needs never be changed.
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
Yes, I noticed that it hit the forward stop at about 2/3 throttle. I don't think it is out of adjustment, I just think it needs lubed and resynced with the carbs because I had them off, and now my timing is off by ~4 degrees, until I move that advance up just a hair. My theory is that the "lean sneeze" is only affecting the one cylinder because it is furthest from the manifold. Once I move the lever to where it is supposed to be, the sneeze dissipates and it idles perfectly smooth as it should, I'll look at the link & sync right now, the whole assembly confuses me a bit so I hope the instructions shed a little light.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Your idle timing isn't really relevant to how the motor runs. It's used to set the idle speed and "is what it is".

A lean sneeze on one hole only can't be anything to do with intake length as all four are the same exact length/volume. Causes: lean mixture due to clogged idle jet/idle pasage, leak at the carb to intake, leak at the intake to block, leak at the bypass cover, leak at the crankcase centerline, damaged reed (check at idle - hold a card in front of each carb throat and look for an even mist of sprayback from each).
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
I see what you're saying...just odd because with the idle timing set where it should be, the sneeze was eliminated completely...I went through all of the passages but I will do so again tonight just to be sure. I will also replace the gasket from carb to motor because I have one in stock. I have also considered reeds, but wanted to eliminate all of the simple things first. Would you happen to have a link to the link & sync procedure? I looked at the stickies and all I could find was timing set at WOT
 

Jmcjunkin3

Seaman Apprentice
Thread starter
Joined
Jul 15, 2017
Messages
49
Wait I just caught myself. Setting it at WOT takes care of idle. I think I should be okay if I can get the linkage to move with the throttle
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Remove throttle cable from motor and set top of throttle arm fully back. Make sure the roller is not touching the throttle cam.

Both carbs need to have their throttle plates completely closed at idle. Adjust the link between the two so they open exactly at the same time.

Now set the throttle roller so it just touches the throttle cam at the small mark (not the one marked START) as you move the throttle arm forward.

Edit: you need to get the split pins and washers back on the throttle linkage. Might cause problems with hangups otherwise. I hope you've not adjusted the threaded rod where it goes in the nylon trunnion.
 
Last edited:
Top