82 Evinrude 15hp Won't run

00Mach1

Recruit
Thread starter
Joined
May 12, 2016
Messages
4
Hey guys new to the forum, I have a 1982 15hp Evinrude 2 stroke E15RCNC that I bought with a John boat a few years ago.. Motor ran good with a few hiccups every once in a while until the last boat outing when it just died on me heading in from fishing.. the motor would stumble and wouldnt run that great unless I pulled out the choke.. Bottom cylinder is wet and with fuel, but the motor will run on the top cylinder with the bottom plug out..

I've replaced the fuel pump and rebuilt the carb with no luck and can't find anyone around that will work on this thing so I'm thinking about trying to fix it myself..

Anybody have any ideas as to what it possibly might be? Thought possibly it could be the leaf (reed) valve but it isn't spitting put the carb like I have read on a few other threads.. Compression test was a tad bit lower on the bottom cylinder (105 on the top and 95 on the bottom)

Any help would be greatly appreciated guys!!

Thanks
Jonathan
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Might want to take its temperature. I had similar problems with my '82, accompanied by some overheating. A PO had done a bad installation of a t.stat and gasket, and I replaced the head gasket, along with the t.stat and gasket (along with a carb rebuild and fuel pump like you did). While working on it I replaced the impeller. Motor runs fine.

If you get into it, the thermostat is located in a tough place at the bottom of the head -- best to take off the head and the t.stat with it. Resurface both the head cover and t.stat cover. Leave the two bottom head bolts loose but in place to pull the head, and insert them in the cover when reassembling. Tight clearances. The t.stat and gasket/cover are best installed on the workbench.
 

00Mach1

Recruit
Thread starter
Joined
May 12, 2016
Messages
4
Might want to take its temperature. I had similar problems with my '82, accompanied by some overheating. A PO had done a bad installation of a t.stat and gasket, and I replaced the head gasket, along with the t.stat and gasket (along with a carb rebuild and fuel pump like you did). While working on it I replaced the impeller. Motor runs fine.

If you get into it, the thermostat is located in a tough place at the bottom of the head -- best to take off the head and the t.stat with it. Resurface both the head cover and t.stat cover. Leave the two bottom head bolts loose but in place to pull the head, and insert them in the cover when reassembling. Tight clearances. The t.stat and gasket/cover are best installed on the workbench.

It should still run even if it overheated correct? I'm a auto mechanic so i would think it should still run in theory but i have never messed with an outboard so i may be totally wrong! Lol I did notice when I removed the old fuel pump there was no gasket there so I didn't put the thick one on when I replaced it.. I also checked and got good spark on both cylinders, and have replaced the plugs..
 
Last edited:

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
You have to put the thick gasket on the fuel pump or your crankcase pulses are being lost to the atmosphere no seal is being made without it. Yes it will run overheated right to the point where it locks up.
 

00Mach1

Recruit
Thread starter
Joined
May 12, 2016
Messages
4
You have to put the thick gasket on the fuel pump or your crankcase pulses are being lost to the atmosphere no seal is being made without it. Yes it will run overheated right to the point where it locks up.

Motor ran fine up till it bogged down on me under throttle and died.. The only reason I didn't put the thick gasket on was because it didn't have it on the old one (not to say it was correct) and noticed it has a bump around the port on the fuel pump.. Also the mounting screws didn't look long enough but I should have checked it with the gasket on..

It will crank up and run for about 2-5 seconds with choke put then dies and won't restart.. it tries to start but won't with bottom spark plug in..
 
Last edited:

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
...and it will run hot, until it don't. (don't want it to seize up) Unfortunately, can't check operating temp if it isn't operating.

Chances are, you would have noticed if it was seriously overheated (smells hot, paint discoloration -- obviously hot to touch). But a typical effect of some degree of overheating is a blown head gasket, and warpage of the head cover -- which also yields continuing operation issues.
 

00Mach1

Recruit
Thread starter
Joined
May 12, 2016
Messages
4
...and it will run hot, until it don't. (don't want it to seize up) Unfortunately, can't check operating temp if it isn't operating.

Chances are, you would have noticed if it was seriously overheated (smells hot, paint discoloration -- obviously hot to touch). But a typical effect of some degree of overheating is a blown head gasket, and warpage of the head cover -- which also yields continuing operation issues.

I don't think it overheated, pretty sure I would have noticed it as you mentioned.. gonna build a motor stand this week for it and bring it in the garage to troubleshoot as the boat is in storage and I don't have the room for it.. first I'll put the fuel pump gasket on and rule that out..
 
Top