72 evinrude 50hp Hydro electric shift.

yota08

Cadet
Thread starter
Joined
Mar 6, 2017
Messages
20
the pontoon I had got recently motor was said to be running. It turns and sounds good but not a big fan of the button shifting control box. Dude before appearantly messed with it before and wires are not connected and wires don’t seem to go to the right spot. I think it’s stuck on forward. Does anybody have a idea which wire is which and what goes where. He had gotten the ignition to start the motor correct but it don’t shift when buttons are pushed. The control box’s is in pretty rough shape really but any help please?
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
72 Hydro-Electric defaults to forward...

If power is supplied to the Green wire, you get Neutral.
If power is supplied to BOTH Green and Blue, you get Reverse..

No power to either Green or Blue is Fwd... (default..)

To Add: I think I'd probably take a multi-meter, and ohm the solenoids out...
From green to ground should be between 5 and 6 ohms resistance..
Same for Blue to ground...
If true in your case, then should be good to go in that respect..

If not, either solenoids are bad, or problem with wires...
 
Last edited:

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
OH!!
And in case you're not aware, you MUST use Type 'C' gear oil in that lower unit... Regular gear oil is no good...
Make sure it's labeled "For use in electric shift"...

That is VERY important....
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Not sure how the push button style shift selector is wired..
I have a 72 Johnson 50hp with Hydro-Electric, but my shifter switch was built into the remote and triggered by the throttle lever..
(Had to Mod it though, as switch was broken and wasn't going to pay $350+ for a new switch...)

Anyway, I imagine there's a red power wire going into the push buttons, then the switch handles sending power between none, green, blue and green, so only blue and green come out..
Probably a white wire (going in or out) in there too for the start in neutral safety, but not sure...

Wish I knew more on the push button style....
 

yota08

Cadet
Thread starter
Joined
Mar 6, 2017
Messages
20
Jboute how did you mod it? I had used to have a 50hp johnson I forget what year but it was 70 something and it was electric shift but I never had a problem to it. But this one has bottons and there wires clipped and wires that don’t match up to where it’s supposed to go.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Here's the link to what I did to replace my shift switch...

https://forums.iboats.com/forum/eng...c-shift-switch-solution-hope-it-helps-someone

Please bear in mind though, that mine didn't have the push buttons, so this may give you ideas, but I'm not sure it would apply exactly in your case...

Truthfully, getting the factory service manual as boobie suggested is the right way to go if you plan on keeping this engine.. LOL

I got mine for about 50-55 bucks including shipping... (can't remember exact total..) from outboardbooks website..
iBoats does sell some manuals which can be helpful, but to my knowledge they aren't the factory service manual..

That said, I'll be happy to answer any questions I can regarding this...
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
You may already know this, but it won't shift unless the motor is running. When not running, it defaults to forward. Also, that motor requires a control with a yellow plug where it connects to the motor. The yellow plug was only used a couple of years.

Slide the rubber insulator sleeves back to expose and disconnect the wires leading down to the lower unit. Then, using a jumper wire, connect the battery to the green wire and it should go into neutral. Jump to both green and blue at the same time and it should go into reverse. If it passes this test, you know the shift is working.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
And just as an FYI...

I just looked through my factory service manual for my Johnson 50..
The wiring diagram doesn't show how the shift switch itself is wired (internally).. It just indicates the wires that go into and out of the switch.. (basically, match colors to colors..)

Since the Johnson and Evinrude are virtually identical, I bet you'll get the same wiring diagram in yours as I have in mine..
(Which is PRICELESS by the way, don't get me wrong!!)

There is however a section on the remote control which better covers the shift switch..
Mine of course covers the style in the remote that came with my Johnson 50 hp, but it includes info on removal, installation, testing etc.. for the switch itself.

Betting the factory manual for your model number will have a remote control section which covers those topics for the push button style switch..

So while it's probably not in the wiring diagram itself, between the iBoats forum, the factory manual wiring diagram, and the factory manual section on remote controls, you should have everything you need to know... :D

(And to correct myself.... Earlier, I said I imagined a red wire going into the switch for power (That may or may not be correct for Evinrude).. It's actually purple, not red for my Johnson 50. The manual jogged my memory.. lol!!)
 
Last edited:

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
You can use the Johnson Control if you don't like Evinrude push button control
 
Top