70 Evinrude overheating w/new pump and thermostat

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Each owner replaced the water pump and thermostat in their respective motors. They get a steady stream of water out the telltale and two idle relief ports at the top of the motor leg. So the engines are pumping great

(1) The pee stream tells you nothing about cooling on a Johnrude as it a water pump indicator..just tells you it is working.
(2) The t-stat or poppet has a problem as there should only none to a very small trickle out of idle relief at idle. Flow will increase with water pressure/RPM and temperature increase.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Thanks! That was one of the best motors I have ever owned. Sold it to get a bigger boat, and I sure do miss it. But my vote for the 3 cylinder E-rudes of that era is YES!

you're welcome, Sutor! It really is a fine looking '84. Happens a sister motor ('85) came up here last summer on a tin hull I liked -- passed on it because it was made clear to me another rig was going to one too many. But it's a new year....
 
G

Guest

Guest
Gentleman I sincerely appreciate all your helpful input.

I personally changed the water-pump on the 89 and I can report the the old one was not in pieces when I changed it. Everything went together with no fuss.

Faztbullet - When I mentioned normal flow out the idle relief ports, I meant it was normal (trickle at idle and increased flow with more throttle)

When I changed the thermostat and heat sensor in the 89, It showed no signs of blockage or build-up in the t-stat cavity.

The owner of the 95 model says the motor will run fine without the thermostat. Which leads me to think that there may be blockage somewhere else that is causing the motor to starve for cooling water, because the thermostat's mere presence in the cavity is restricting the flow enough to cause an overheat. The 95 owner did report that he noticed a build-up of sediment in and around the the T-stat cavity, so Logic tells me it has to be else-ware too.

I'll re-examine the telltale on the 89, but the OMC bulletin I obtained for the tell tale hose relocation says it applies to post '94 motors.

Its a odd thing guys, I've been around these great motors my whole life, and I even owned a couple of them, but I've never seen one act like this before.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
sounds like a good lead with the '95. Would want to make sure the bypass in the t.stat housing is clear. Another lister mentioned using a vinegar flush in his to help clear salt buildup -- don't know if that is successful, and there are probably products on the market. Running in salt water, my sense was always that the passages have to be opened up periodically and physically cleaned out.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
The only way the exhaust ports on the 89 should should be trickling water is if it's on muffs. In the the water it should be throwing a ton out of the relief ports warm or not. I have the same motor it's an 86 and pumps water like a fire truck. The service bulletin you need is 2276 Rev. 1 for the telltale relocation covers 1986-1994 56 ID blocks only. People will tell it goes in the head of the motor IT DOES NOT IT GOES ON TOP OF THE EXHAUST HOUSING. You also will need water pump kit 04322955 this has the parts to finish the relocation. The kit contains the new thermostat spring and gaskets you need also has the grommet for the telltale outlet replacement. There is a grommet to go in the outlet hole and it will pump straight out of the hose unrestricted. These changes were because of a pump design change going from 3 blade to 5 blade pumps. The 5 blade pumped so much water that it could overcome the spring for the thermostat and effectively bypass it. They use the unrestricted tattletale as a pressure relief also add a stronger spring to the thermostat.

The reasons for the hose relocation is
#1 the motor is idling with a restricted or blocked thermostat bypass hole
#2 the engine operates in aerated water such as the wake of a pontoon boat.

Do the water pump updates and remove the telltale outlet
 

joetheis

Petty Officer 1st Class
Joined
Apr 21, 2014
Messages
308
Could it have over heated and now a bad head gasket/head or cracked block?
I was a Chrysler Tech for a number of years, overheat would send up red flag, exhaust going into coolant, and over heating.
Also remove Thermo, take a hose and back flush??
Joe
Take any advice I give with a can of beer er 2!
 
Last edited:
Top