68' 15hp johnson shift problem

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
If it's a long shaft, you may only see one bolt on the shift connector, as the connector is 5-inches longer. You'd only see the upper bolt...
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
If it's the long coupler, you'll have to drop the lower unit to get to the lower shift rod hookup. The gear shift will move back and forth as it should, but if the lower shift rod is not properly positioned/secured in the coupler, that could be why it's not going into forward. To go into forward, the shift rod has to be raised up, so if the lower coupler bolt is missing, the motor would shift into reverse ok (pushed down) but wouldn't raise the shift rod to engage forward when you move the gear shift lever to forward. Does that make sense?
 

Ostromk45

Cadet
Thread starter
Joined
Mar 19, 2016
Messages
14
Yes it does and yes its a long shaft. I pulled the lower unit had a brain fart and forgot to look and see if the rod was properly hooked up before removing the bolt and hooking it up right but its hooked up right now for sure lol. Was in the process of bolting the lower unit back on then the wife pulled me off to do something else so if not tonight i will get it all back together tomorrow and tested.
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
While you have the L/U off, you can test the gears - push the shift rod down and turn the driveshaft - prop will turn one direction. Now pull the shift rod up and turn the driveshaft - prop should turn the opposite direction. Shift lever in middle - prop shouldn't turn.
 

Ostromk45

Cadet
Thread starter
Joined
Mar 19, 2016
Messages
14
Ok i did that and in neutral the prop turns freely both directions like it should then in forward it spins and turns the shaft now i dont know if its suppose to do this but in forward. I can also turn it the opposite way and it turns the shaft. I put it in reverse and it does the same thing is this correct? Is their anything else need to check before I put the lower unit back on?
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
That's as it should be. While you've got it off is a good time to replace the impeller.
 

Ostromk45

Cadet
Thread starter
Joined
Mar 19, 2016
Messages
14
Well after fighting to get the lower unit on for a day and a half got everything back together started her up and still nothing in forward the shift lever just shakes like all get out when i try to put it in forward :-(
 

baldwisa

Seaman
Joined
Aug 3, 2015
Messages
73
I'm curious about your issue. I have a 1968 60hp sportfour manual shifter. After replacing the lower seals and putting the shift rods back into the connectors I have no forward gear. It makes a clicking noise when I try to shift it into forward.
 

Ostromk45

Cadet
Thread starter
Joined
Mar 19, 2016
Messages
14
No clicking here it just wont catch forward gear what else could cause this
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
might reach in with a screwdriver or punch and see if you can move the rod up by hand (i.e., shift into gear by hand). If it was working normally when the l.u. was removed, would suspect linkage elsewhere (incl. that brass connector). Don't mean to flog dead horses, but need to be sure the rod is properly attached at each end of that 5" connector.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Make that "properly attached" at both ends. The clamp can grip the shift rod even with the bolt not aligned in the groove on the shift rod.

Another thing to check - is the shift handle up top tight on the shaft? It has an oblong slot in it that allows for fore and aft adjustment. Might be time to loosen up the TWO bolts on the shift handle and see if you can re-center the handle to the shaft. See if the shift shaft can rotate far enough, free of the handle (and its stop) to engage forward gear.
 
Top