'64 evinrude 18hp - Ughh! problems since buying

fanuminski

Recruit
Thread starter
Joined
Jun 22, 2003
Messages
4
I bought this motor several weeks ago. 1st time out, wasn't getting gas and I rebuilt the carb which<br />seemed to solve the problem except for a miss at low<br />idle. The only way to keep it running was to put it<br />in gear and start it with the throtte open a little<br />bit more. Ran good at high speed. Last time out, <br />it started in nuetral, placed it in reverse and <br />backed out of bay. Motor died. When I got it started again, it would not work in either reverse<br />or forward. The linkage seems to be working -<br />is there a shear pin or prop pin that may have busted<br />to prevent gear damage, or do I give up on this<br />motor? Should I also think about replacing the<br />points/coil to solve the missing? <br />Thanks for any help you can give me - I wish their<br />were repair people/places willing to work on older<br />models in the twin city/mn. area.
 

fanuminski

Recruit
Thread starter
Joined
Jun 22, 2003
Messages
4
Re: '64 evinrude 18hp - Ughh! problems since buying

"^" 12footer, I'm hoping for some help from you!
 

12Footer

Fleet Admiral
Joined
Mar 25, 2001
Messages
8,217
Re: '64 evinrude 18hp - Ughh! problems since buying

Sorry didn't notice a zero-reply ,so skipped right over this...It's an evinrude too hhmmm..<br /><br />A miss at low idle is a more than likely, A miss at all speeds, just not as noticeable.<br />A motor of this vintage could have poor compression, and would be the first thing I checked. Compression is vital, and low compression would cause the symptoms you describe.<br /><br />If the boat would not go when placed in gear, and just revs-up, the shear pin has probably been sheared. Remove the prop, and pin. If the pin comes out in three pieces, it has sheared, and needs to be replaced. Get a box of them, and keep them on board.
 

fanuminski

Recruit
Thread starter
Joined
Jun 22, 2003
Messages
4
Re: '64 evinrude 18hp - Ughh! problems since buying

thanks for the reply 12footer - I will be checking the compression next. What do you think about<br />pulling the flywheel and replacing the points and/or<br />coil/condensor - could this cure my missing problem?<br />"^"
 

Fouled Plug

Ensign
Joined
Jun 29, 2001
Messages
935
Re: '64 evinrude 18hp - Ughh! problems since buying

If you have a strong spark to both plugs, your ignition is probably OK. May want to clean and gap the points, but replacing parts in a shotgun approach to troubleshooting can get expen$ive in a hurry. :eek:
 

MajBach

Chief Petty Officer
Joined
Jun 21, 2003
Messages
564
Re: '64 evinrude 18hp - Ughh! problems since buying

My father bought one of these motors new in '64. He gave it to me in '91 and I sold it two years ago. Actually, in '96 I found another one just like it (long story short) with less than 20 hrs on it and paid $150 CAD with four props! The original motor had just started to lose compression that same year (was 90 psi when i checked it) but still ran flawlessly, albeit slower. Anyway, Dad and I sat down one weekend and figured the motor conservatively had 4500 hrs on it and possibly as much as double that. Figuring that half trolling (1.5 mph) and half WOT (20 mph) thats around the Earth almost twice!!<br />We changed the gearcase on the original motor once (drain screw fell out while underway),the impellor 2 or 3 times, each coil twice, the thermosstat once and regular fluids and plugs but nothing more! When I got the new one, the fuel pump and needle valve were 'worn' from never being used and I took the ones from the old one and replaced them. Both motors started second pull maximum at the beginning of each season. I ran the mixture 50:1 BTW. <br />Anyway, my point is, I think this motor is bulletproof and I feel I know it inside out. I certainly would not give up on it! 12 Footer is right about shear pin (I'm not sure if the prop hubs can spin on those older ones). You can use piece of coat hanger in a pinch.<br />As far as it stalling:<br />Make sure micture screw is all the way clockwise - seemed to make a signifcant difference on mine. I have had the similiar problem as you described. I found it common for this motor to miss while trolling at idle. Frequently it would stall but not enough to feel there was something wrong. If one of the coils goes, you will know it. It doesn't seem to 'miss' as much as it sounds like someone is holding onto the prop (perhaps jaws). No way you would get on a plane if one coil was gone. A good indication is that if you open the throttle and the rpms climb and all of a sudden it sounds like the second cylinder kicks in and everything seems normal- you have a bad coil. I suppose the points could need adjusting or cleaning as well. <br />Another problem I experienced three times was stalling at cruise but running fine at idel. this happened three times over the years. Once it was the fuel tanks developing a vaccuum (I had placed a homemade rubber gasket around filler cap 'cause it was always spilling. solution:drilled small hole through cap). Second time it was leaky fuel line from tank - at the point where it connects to the motor. Third time it was with the second low hour motor and it turned out to be the needle valve. It looked perfectly fine but guess it was sticking. I replaced it with valve from old motor (which was noticeably worn) and it worked fine.<br />Feel free to e-mail anytime!<br />majbach@sympatico.ca
 

fanuminski

Recruit
Thread starter
Joined
Jun 22, 2003
Messages
4
Re: '64 evinrude 18hp - Ughh! problems since buying

thanks to everyone who took time to read and offer<br />their advice. I can't wait to try a few of the <br />suggestions. Trying to fish while rowing to spots<br />is not very fun!<br />mike<br />PS> to Majbach : I'll be emailing you
 

MajBach

Chief Petty Officer
Joined
Jun 21, 2003
Messages
564
Re: '64 evinrude 18hp - Ughh! problems since buying

Great! Hey, I just noticed your user ID now. Musky man eh? Same here. <br />I'm guessing 'twin cities' is St.Paul/Minne?<br />Might have to dip the rods together some time. If you're ever out 'Moon River', Ontario way - let me know. I replaced my 18 Fastwin with a Honda 90!. Believe it or not, it gets about 1.5 times better gas mileage on a boat 4 times heavier.
 
Top