63 Bell Boy Ballerina

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Well I'm on my 3rd boat in a month. I began with a 10ft wood trimmed aluminum and restored that for a little extra money. Took those funds and bought a 14ft all aluminum and restored that. Now I finally have a "real" boat. Bought it for 450 with trailer and motor. The motor starts right up but needs a few parts to get her running how I want it. After the motor I buff her out to her real glory.
 

Attachments

  • 00202_bWMzSMnvo8G_600x450-1.jpg
    00202_bWMzSMnvo8G_600x450-1.jpg
    37.1 KB · Views: 2
  • 00M0M_i6Nc8yoaQ1X_600x450.jpg
    00M0M_i6Nc8yoaQ1X_600x450.jpg
    21 KB · Views: 2
  • 00p0p_a9lQpCzCwcv_600x450.jpg
    00p0p_a9lQpCzCwcv_600x450.jpg
    31.9 KB · Views: 1
  • 2015080495182720.jpg
    2015080495182720.jpg
    262.1 KB · Views: 2

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
I'm a sucker for the Old Runabouts! That's a very sleek looking hull design and windshield. She's gunna look great when she's done. What size motor? Is it manual or electric shift? Does the floor have any soft spots? Have you flex tested the transom?
 

sphelps

Supreme Mariner
Joined
Nov 16, 2011
Messages
11,508
Wow ! I agree with Woody ... Very sleek cool hull design .. Watching this one come together for sure ! :pop2:
:welcome: Welcome aboard !
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Thanks for the kind words. The floor is solid, transom is solid. I did the hammer knock test. Planning on switching the swivel seats to the back to back folding ones that turn into beds. The motor is a manual shift Lark IV 40hp.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Thanks for the kind words. The floor is solid, transom is solid. I did the hammer knock test. Planning on switching the swivel seats to the back to back folding ones that turn into beds. The motor is a manual shift Lark IV 40hp.


Uhmm, No Offense but...the Knock test is Totally unreliable especially for a boat of this vintage. The ONLY way to know for sure is to drill core samples and check the shavings. I have a Lark IV Selectric Shift. Very Nice Motors. What do you need to get her running better??
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Yea don't see myself drill holes in my transom. As far as parts go. Ordered a full gearcase seal kit, carb rebuild kit, and had to order all the piece to get the water side of things going. For some reason no one has a kit for the water impeller rebuild. I'll have fun with the boat till summer is over. Then I'll do the ignition part of the motor. Too excited to get out and cruise the lake.
 

jbcurt00

Moderator
Staff member
Joined
Oct 25, 2011
Messages
25,350
Not holes thru the transom, just 1/4"diameter core holes 1-1.25" deep into the transom, from the inside only.

The knock test isnt a very reliable test of condition.

If you need to work on the Lark anyway, you could pull it and take a look at any thru holes used to bolt it to the transom.

Post some pix of the stern, transom, motor mount and splashwell.

That boat didnt come w pedestal seats originally, but the deck doesnt show evidence of the previous seats being mounted.

Whats covering the deck?

Not the original Zolotone finish, perhaps a previous owner did some work to it.

Good luck w your project.

The outboard forum can help sort out the Lark
 
Last edited:

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
The outboard isn't bolted on, it's clamped on. For me it doesn't matter size of hole. I just don't feel the need to be drilling. Thanks
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Uhmmm, There's a LOT of experienced, knowledgeable members on this forum and I think you'd learn a lot about vintage boats and how to inspect them and know that they were structurally sound if you did some research here on the forum. The core sampling technique is a perfectly acceptable and commonly used method for knowing that a transom is not rotting on the inside. It's actually the only way to know for sure. There are hundreds of examples of members just like you with boats just like yours that have done the "Hammer Test" and Thought their transoms were good to go only to find out later that they were rotten to the core and totally unsafe. I truly hope this is not the case for you.

I rebuilt the same motor and found all the parts for her on this site...http://www.laingsoutboards.com/johnsonevinrudeparts.html

I sincerely wish you well with your boat and your safety.
attachment.jpg
 

gm280

Supreme Mariner
Joined
Jun 26, 2011
Messages
14,605
The outboard isn't bolted on, it's clamped on. For me it doesn't matter size of hole. I just don't feel the need to be drilling. Thanks

candyman, I am certainly not here to argue with you by any stretch, but to merely try to explain things to you. What the above folks were trying to say is, with your boat being so old, there is a very high probability that your transom, stringers, and even the floor materials are probably rotted or on their way to total rot. And the serious only way to prove that to yourself, is to take a cordless drill (or any type drill for that matter) and at the lowest possible place on you transom, drill a 1/4" hole into the INSIDE of your boat's transom. IF the drill shavings come out totally dry and light wood colored, you are good to go and you simply refill that core hole with either epoxy or any type marine sealer. IF however, you get dark colored wet shavings, move up a little and drill another sample hole to see how far the rot has progressed. And sadly, I think you will find you have rot onboard. And even though you think your hull is sound, that rot can cause some really serious issue on the water when you least expect it. We are not talking about drilling the holes through the transom, but drill a mere 1" or so and see what you actually have. So there is no possible way you are weakening the transom by no means, but testing to verify that it IS solid as you think. If that still seem undoable to you. That that is your decision... We are just trying to make certain you have a safe hull and enjoy your new-to-you boat... :concern:
 
Last edited:

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
I understand everyone is just trying to share info. I'm not here to argue or anything. I love forums, always good info and great people. I also understand that the drill technique is probably used by thousands of people. Just won't be used by me. Thank you, hope people don't see me as a negative person of this forum.
 

52FordF2

Petty Officer 1st Class
Joined
May 31, 2013
Messages
372
Here another test WOG can explain it better than me. If you raise/tilt the motor up and bounce it. Good transom wont have any deflection. If it deflect check the transom some more. There are plenty of way to skin the cat you know.
 
Top